Wisconsin Combination Vehicles CDL Practice Test

This is a free 20-question practice test for the Combination Vehicles portion of the Wisconsin Commercial Driver's License knowledge exam. Questions are pulled from a pool of 55 drawn from the AAMVA CDL Manual, which is the source document the Wisconsin Division of Motor Vehicles uses to write its actual exam.

How it works: Click an answer. The correct choice highlights in green, and you'll see a short explanation. Aim for 85% or better before you sit for the real test in Wisconsin.

Question 1 of 20

When approaching a curve in a tractor-trailer, you should:

Brake during the curve
Slow down before entering the curve
Speed up
Maintain steady speed

Correct. Slow before entering the curve. Once in the curve, accelerate gently to maintain stability. Braking in a curve invites trailer skid or rollover.

Question 2 of 20

When making a right turn at an intersection in a tractor-trailer:

Swing to the left first to make room for the right turn
Make the turn from the right lane and swing wide as needed at the end of the turn
Make the turn at high speed
Stay in the left lane through the turn

Correct. Make the turn from the right lane. If you must swing wide, do so as you complete the turn, never before — swinging left first invites a vehicle to pass on your right.

Question 3 of 20

Trailer rollover is more likely when:

Cargo is loaded low and centered
Cargo is loaded high or to one side, raising the center of gravity
Cargo is light
Trailer is empty

Correct. High cargo and uneven side-loading raise the center of gravity, increasing rollover risk on curves and ramps.

Question 4 of 20

The trailer hand valve should be used:

Only to test the trailer brakes; never to slow the rig in normal driving
To slow the rig in all conditions
To brake on slick roads
Continuously on long downgrades

Correct. Use the trailer hand valve only for testing trailer brakes. Using it to slow the rig can cause the trailer to skid or jackknife.

Question 5 of 20

A jackknife happens when:

The trailer wheels skid while the tractor continues forward
The tractor pulls forward in a straight line
The trailer slides sideways while the tractor pivots
The driver brakes too lightly

Correct. Jackknife is when the drive wheels skid and the trailer continues forward, causing the tractor to pivot — the rig folds at the fifth wheel like a closing knife.

Question 6 of 20

When backing a tractor-trailer in a straight line, you should:

Let the trailer drift wherever it goes
Make small steering corrections to keep the trailer in line
Apply heavy brake pressure
Use the trailer hand valve

Correct. When backing straight, watch the trailer in your mirrors and make small steering corrections to keep it tracking straight. Big corrections lead to jackknifing.

Question 7 of 20

The air lines connecting the tractor and trailer are:

Red (emergency) and blue (service)
Red and yellow
Blue and yellow
Black and red

Correct. The red glad-hand carries emergency/supply air; the blue glad-hand carries service air. They cross to keep matched colors when coupling.

Question 8 of 20

Before uncoupling, you should:

Park on level ground, set the trailer parking brake, lower the landing gear, disconnect air and electrical lines, then release the fifth-wheel jaws
Just pull away
Disconnect electrical only
Drive forward fast

Correct. Proper sequence: park level, lower landing gear to support the trailer, disconnect lines, release jaws, then pull forward slowly. Skipping any step risks dropping the trailer.

Question 9 of 20

Length and weight increase what about a combination vehicle?

Stopping distance, off-tracking, blind spots, and time required for lane changes
Visibility
Speed
Acceleration

Correct. Longer, heavier rigs need more stopping distance, swing wider in turns, have larger blind spots, and require more time and space to change lanes.

Question 10 of 20

A high-mounted trailer kingpin is dangerous because:

It will not engage the fifth wheel and the trailer can drop
It is illegal
It improves coupling
It changes color

Correct. If the trailer is too high, the fifth wheel slides under without the kingpin engaging the locking jaws. The trailer is not coupled and can drop when you pull away.

Question 11 of 20

When you supply air to the trailer for the first time after coupling, you should:

Wait until air pressure builds in the trailer reservoir, then test the trailer brakes by pulling out the trailer-supply knob
Drive away immediately
Disconnect the lines
Skip the test

Correct. Charge the trailer system. Then test the trailer brake function by tugging gently or pulling the trailer-supply knob to confirm trailer brakes apply.

Question 12 of 20

Cargo securement: the heaviest part of the load should be:

Loaded over the front axle area, with weight evenly distributed side to side
Loaded at the rear
Loaded on one side
Stacked on top

Correct. Loading heavy cargo to the front of the trailer over the drive axles helps with traction; loading to one side or top creates dangerous handling.

Question 13 of 20

After connecting the trailer, before pulling away, you should always:

Visually inspect the fifth-wheel/kingpin connection from outside the cab
Just trust the gauge
Honk the horn
Set the trailer brake

Correct. Always visually confirm: no gap between fifth wheel and trailer plate, jaws closed around the kingpin shank, locking lever fully in place.

Question 14 of 20

If the trailer is too low for coupling, you should:

Crank the trailer up with the landing gear before backing under
Skip the inspection
Drive faster
Use the trailer brake

Correct. Use the landing gear hand crank to raise the trailer to the proper height (just below fifth-wheel level) before backing under.

Question 15 of 20

When inspecting the kingpin during pre-trip, look for:

Excessive wear, bending, cracks, or improper lock-jaw engagement
Only the color
Only the size
Only the grease

Correct. A worn, cracked, or bent kingpin can fail under load. The locking jaws must close completely around the shank, not just the head.

Question 16 of 20

When you check the fifth wheel during pre-trip, you look for:

Mounting to the frame is secure, no missing or damaged parts, no visible space between the upper and lower fifth-wheel plates, locking jaws around the kingpin shank, release arm in the locked position
Only the color
Only the bolts
Only the grease

Correct. Check mount, condition, gap, jaw engagement around kingpin shank (not the head), and release-arm lock position. Lubrication should be present but not excessive.

Question 17 of 20

A trailer that has been sitting may have:

Brakes that need careful adjustment, rust on the kingpin, or other issues that should be inspected
No issues — trailers are static
Built-in safety
Better brakes

Correct. Trailers idle for long periods can develop brake corrosion, kingpin rust, low tires, and other issues. Inspect carefully before use.

Question 18 of 20

On a slippery surface, drive in:

Higher gears at higher RPM
A gear that minimizes torque to the drive wheels and brake earlier and gentler
The lowest gear
Whatever is fastest

Correct. Reduce engine power to drive wheels (higher gear, gentler accelerator) and brake earlier and gentler to avoid wheel spin or skid.

Question 19 of 20

Your trailer ABS warning lamp is on. The trailer service brakes:

Will not work at all
Still work normally — only ABS function is unavailable
Lock up
Apply automatically

Correct. Trailer service brakes still work normally without ABS. Have the system repaired; ABS gives extra control during emergency braking.

Question 20 of 20

On a tight curve or exit ramp, a tractor-trailer is most likely to roll over because:

The trailer brakes lock
The high center of gravity creates a tipping force greater than the tires can resist
The tractor accelerates
The road is dry

Correct. Centripetal forces in a curve push the cargo outward; a high center of gravity multiplies the tipping moment. Slow before the curve.

About the Wisconsin Combination Vehicles exam

Most states administer 20 Combination Vehicles questions and require 80% to pass. The exam emphasizes the unique handling of articulated vehicles: how trailers track behind the tractor, how to prevent rollover, how to manage rearward amplification with multi-trailer combinations, and the correct sequence to couple and uncouple.

The Wisconsin Division of Motor Vehicles follows the federal CDL standards established by FMCSA. To earn the Combination Vehicles credential, you must answer at least 80% of the questions correctly. Many candidates score lower the first time because the test pulls from a large pool — refreshing this page will give you a different mix of questions, drawn from the same authoritative source.

Want more practice? Try the full Combination Vehicles question bank or browse all Wisconsin CDL practice tests.