Washington Combination Vehicles CDL Practice Test

This is a free 20-question practice test for the Combination Vehicles portion of the Washington Commercial Driver's License knowledge exam. Questions are pulled from a pool of 55 drawn from the AAMVA CDL Manual, which is the source document the Washington State Department of Licensing uses to write its actual exam.

How it works: Click an answer. The correct choice highlights in green, and you'll see a short explanation. Aim for 85% or better before you sit for the real test in Washington.

Question 1 of 20

The trailer hand valve should be used:

Only to test the trailer brakes; never to slow the rig in normal driving
To slow the rig in all conditions
To brake on slick roads
Continuously on long downgrades

Correct. Use the trailer hand valve only for testing trailer brakes. Using it to slow the rig can cause the trailer to skid or jackknife.

Question 2 of 20

Combination vehicles are usually:

Easier to drive than single trucks
Harder to drive than single trucks because of length, weight, and the unique handling of articulated vehicles
The same as single trucks
Faster than single trucks

Correct. Combination vehicles (tractor-trailer rigs) are heavier, longer, and articulate at the fifth wheel — all making them more demanding than single-unit trucks.

Question 3 of 20

A jackknife happens when:

The trailer wheels skid while the tractor continues forward
The tractor pulls forward in a straight line
The trailer slides sideways while the tractor pivots
The driver brakes too lightly

Correct. Jackknife is when the drive wheels skid and the trailer continues forward, causing the tractor to pivot — the rig folds at the fifth wheel like a closing knife.

Question 4 of 20

Trailer rollover is more likely when:

Cargo is loaded low and centered
Cargo is loaded high or to one side, raising the center of gravity
Cargo is light
Trailer is empty

Correct. High cargo and uneven side-loading raise the center of gravity, increasing rollover risk on curves and ramps.

Question 5 of 20

When uncoupling, you should lower the landing gear:

After releasing the jaws
Before releasing the jaws so the trailer is supported when you pull away
Halfway
Not at all

Correct. Lower the landing gear and snug it against the ground before releasing the fifth-wheel jaws so the trailer doesn't drop when you pull away.

Question 6 of 20

A combination vehicle requires more time to stop than a single vehicle because:

It is much heavier and air must travel further to reach the trailer brakes
It accelerates faster
It is shorter
Drivers wait longer

Correct. Greater weight + brake-lag in long air lines = longer stopping distance. Plan ahead.

Question 7 of 20

When you "G.O.A.L." in trucking, you:

Get Off And Look — visually verify the area before backing
Go Over A Limit
Grab On And Lift
Greet Other Approaching Loaders

Correct. G.O.A.L. — Get Out And Look — is the universal driver-school rule before any tight backing maneuver.

Question 8 of 20

When making a right turn at an intersection in a tractor-trailer:

Swing to the left first to make room for the right turn
Make the turn from the right lane and swing wide as needed at the end of the turn
Make the turn at high speed
Stay in the left lane through the turn

Correct. Make the turn from the right lane. If you must swing wide, do so as you complete the turn, never before — swinging left first invites a vehicle to pass on your right.

Question 9 of 20

On a tight curve or exit ramp, a tractor-trailer is most likely to roll over because:

The trailer brakes lock
The high center of gravity creates a tipping force greater than the tires can resist
The tractor accelerates
The road is dry

Correct. Centripetal forces in a curve push the cargo outward; a high center of gravity multiplies the tipping moment. Slow before the curve.

Question 10 of 20

When you supply air to the trailer for the first time after coupling, you should:

Wait until air pressure builds in the trailer reservoir, then test the trailer brakes by pulling out the trailer-supply knob
Drive away immediately
Disconnect the lines
Skip the test

Correct. Charge the trailer system. Then test the trailer brake function by tugging gently or pulling the trailer-supply knob to confirm trailer brakes apply.

Question 11 of 20

When making a U-turn, a tractor-trailer needs:

Less space than a car
Substantially more space than a car — often more than a single intersection allows
The same space as a car
No turning space

Correct. Tractor-trailer turning radius is much larger than a car. A standard intersection rarely allows a U-turn — find a wider turning area.

Question 12 of 20

When backing a tractor-trailer in a straight line, you should:

Let the trailer drift wherever it goes
Make small steering corrections to keep the trailer in line
Apply heavy brake pressure
Use the trailer hand valve

Correct. When backing straight, watch the trailer in your mirrors and make small steering corrections to keep it tracking straight. Big corrections lead to jackknifing.

Question 13 of 20

Most jackknifes happen because:

Drive wheels skid during braking on slippery surfaces
Brakes work too well
The road is dry
Cargo is too light

Correct. Loss of traction on the tractor drive axles during braking — typically on slick surfaces or with overly aggressive braking — causes a jackknife.

Question 14 of 20

When you couple, the locking jaws of the fifth wheel must close around:

The kingpin shank, not just the head
Just the head
The trailer skirt
The wheel

Correct. The locking jaws must engage the kingpin shank below the head. If the jaws close above the head, the connection is unsafe.

Question 15 of 20

Before uncoupling, you should:

Park on level ground, set the trailer parking brake, lower the landing gear, disconnect air and electrical lines, then release the fifth-wheel jaws
Just pull away
Disconnect electrical only
Drive forward fast

Correct. Proper sequence: park level, lower landing gear to support the trailer, disconnect lines, release jaws, then pull forward slowly. Skipping any step risks dropping the trailer.

Question 16 of 20

When approaching a curve in a tractor-trailer, you should:

Brake during the curve
Slow down before entering the curve
Speed up
Maintain steady speed

Correct. Slow before entering the curve. Once in the curve, accelerate gently to maintain stability. Braking in a curve invites trailer skid or rollover.

Question 17 of 20

Which is the proper following distance for a 60-foot rig at 50 mph?

3 seconds
6 seconds
7 seconds
12 seconds

Correct. 1 second per 10 feet at speeds below 40 mph, plus 1 extra second above 40. 60 feet = 6 seconds + 1 = 7 seconds at highway speed.

Question 18 of 20

The air lines connecting the tractor and trailer are:

Red (emergency) and blue (service)
Red and yellow
Blue and yellow
Black and red

Correct. The red glad-hand carries emergency/supply air; the blue glad-hand carries service air. They cross to keep matched colors when coupling.

Question 19 of 20

When you check the fifth wheel during pre-trip, you look for:

Mounting to the frame is secure, no missing or damaged parts, no visible space between the upper and lower fifth-wheel plates, locking jaws around the kingpin shank, release arm in the locked position
Only the color
Only the bolts
Only the grease

Correct. Check mount, condition, gap, jaw engagement around kingpin shank (not the head), and release-arm lock position. Lubrication should be present but not excessive.

Question 20 of 20

A sliding fifth wheel that is unlocked or improperly secured can:

Slide unexpectedly during braking or acceleration, dangerously changing handling
Improve fuel economy
Save time
Have no effect

Correct. An unsecured sliding fifth wheel can shift during braking, changing the rig's handling unpredictably. Always verify the lock pin is engaged.

About the Washington Combination Vehicles exam

Most states administer 20 Combination Vehicles questions and require 80% to pass. The exam emphasizes the unique handling of articulated vehicles: how trailers track behind the tractor, how to prevent rollover, how to manage rearward amplification with multi-trailer combinations, and the correct sequence to couple and uncouple.

The Washington State Department of Licensing follows the federal CDL standards established by FMCSA. To earn the Combination Vehicles credential, you must answer at least 80% of the questions correctly. Many candidates score lower the first time because the test pulls from a large pool — refreshing this page will give you a different mix of questions, drawn from the same authoritative source.

Want more practice? Try the full Combination Vehicles question bank or browse all Washington CDL practice tests.