Vermont Doubles/Triples CDL Practice Test

This is a free 20-question practice test for the Doubles/Triples portion of the Vermont Commercial Driver's License knowledge exam. Questions are pulled from a pool of 50 drawn from the AAMVA CDL Manual, which is the source document the Vermont Department of Motor Vehicles uses to write its actual exam.

How it works: Click an answer. The correct choice highlights in green, and you'll see a short explanation. Aim for 85% or better before you sit for the real test in Vermont.

Question 1 of 20

The "T" endorsement is required to:

Drive any commercial vehicle
Pull two or more trailers
Drive a bus
Haul hazmat

Correct. The T endorsement is required to pull more than one trailer (doubles or triples).

Question 2 of 20

Crosswinds are particularly hazardous for:

Empty doubles and triples
Loaded singles
Backing
Slow speeds

Correct. Empty trailers in a multi-trailer rig present a large flat surface to crosswinds — a strong gust can blow the rear trailer over.

Question 3 of 20

Drivers should always couple the heaviest trailer:

Behind the tractor (in the front position)
At the rear
In the middle
It does not matter

Correct. Heaviest trailer goes directly behind the tractor; lightest goes at the rear. This minimizes rearward amplification and rollover risk.

Question 4 of 20

A pintle hook is:

The hitch on the rear of a trailer used to tow another trailer or dolly
The kingpin
The fifth wheel
A type of placard

Correct. The pintle hook is the strong rear-mounted hitch that grips the dolly's lunette eye, allowing one trailer to tow another behind it.

Question 5 of 20

In a multi-trailer combination, the most violent movement during evasive maneuvers happens at:

The tractor
The first trailer
The last trailer
The cab

Correct. Rearward amplification (crack-the-whip effect) is greatest at the rear-most trailer. The last trailer in a triple can be thrown sideways with much greater force than the tractor.

Question 6 of 20

A converter dolly is:

A small hand truck
A set of axles with a fifth wheel that converts a semi-trailer into a full trailer for use in doubles/triples
A trailer-loading device
A type of brake

Correct. A converter dolly has a small frame, axle(s), and a fifth wheel mounted on top — it transforms a semi-trailer into a full trailer behind another trailer.

Question 7 of 20

You discover a flat tire on the rear trailer of a triple. You should:

Continue driving
Pull off safely, set warning devices, and have the tire repaired or replaced before continuing
Drive only at night
Drive faster to balance

Correct. A flat tire affects rig stability and brake load. Pull off safely, use warning devices, and address the tire.

Question 8 of 20

When inspecting a converter dolly, the pintle hook must:

Lock fully closed around the lunette eye
Be loose
Be cracked
Be replaced quarterly

Correct. The pintle hook must close fully around the lunette eye, with no excessive wear or cracks. Add safety chains as backup.

Question 9 of 20

When backing a doubles or triples combination:

Avoid it whenever possible — multi-trailer rigs cannot be backed any meaningful distance safely
Back at full speed
Back without a helper
Use only the trailer brake

Correct. Doubles and triples cannot be backed safely beyond a few feet — joints flex unpredictably. Plan your route and parking to avoid backing.

Question 10 of 20

On a triple, the air pressure to the rearmost trailer:

Is the same as the lead
Is delayed by line length, so braking response at the rear trailer lags noticeably
Is faster
Does not exist

Correct. Greater line length = greater brake-lag at the rear. Plan braking earlier than you would for a single trailer.

Question 11 of 20

Air pressure on a triple-trailer rig takes:

Less time to reach the rear trailer than on a single
Significantly more time to reach the rear trailer's brake chambers
The same time
No air pressure is needed

Correct. Each additional trailer adds line length. Brake response at the rear trailer of a triple is noticeably delayed — brake earlier.

Question 12 of 20

A "set of triples" typically refers to:

One tractor pulling three trailers
Three trailers without a tractor
Three tractors and one trailer
Three tractors only

Correct. A set of triples is one tractor pulling three trailers — usually allowed only on specific designated routes.

Question 13 of 20

When inspecting a doubles or triples rig, you should additionally check:

Each pintle hook, each set of safety chains, each converter dolly, each trailer's lights, brake chamber connections, glad-hands, and shut-off valves
Only the lead trailer
Only the tractor
Only the cargo

Correct. Every connection point and every trailer needs inspection — pintle hooks, chains, dollies, lights, brake lines, glad-hands, and air-supply valves.

Question 14 of 20

Inspecting safety chains on a converter dolly:

Verify they are correctly crossed and have no broken links, deformations, or wear
Skip the chains
Replace them daily
Verify color only

Correct. Safety chains should be intact, no broken links or excessive wear, and properly crossed under the pintle for support.

Question 15 of 20

Crosswinds may cause the rear trailer of a doubles to:

Sway dangerously, especially when empty
Brake automatically
Steer itself
Have no effect

Correct. Empty trailers act as sails. Strong crosswinds can sway or even tip an empty rear trailer. Reduce speed in high winds.

Question 16 of 20

Coupling order for a set of doubles starts with:

Coupling the lead (front) trailer to the tractor first, charging air, then attaching the converter dolly to the rear of the lead trailer, then attaching the second trailer
Coupling the rear trailer first
Coupling the dolly first
It does not matter

Correct. Standard order: tractor + lead trailer first, charge air, then attach converter dolly behind lead trailer, then second trailer to dolly.

Question 17 of 20

You should never:

Quickly steer to the left while pulling triples
Drive at the speed limit
Use turn signals
Stop at intersections

Correct. Sudden steering with triples can cause the rear trailer to roll. Avoid abrupt steering and plan lane changes far in advance.

Question 18 of 20

When pulling a heavy lead trailer and a light second trailer, the rig:

Will be more stable than the reverse
Is more likely to roll the rear trailer
Is illegal
Drives the same as either order

Correct. Heaviest in front, lightest in rear. Heavy at the rear amplifies crack-the-whip and rollover risk.

Question 19 of 20

A tractor pulling doubles cannot brake as quickly as a tractor pulling a single trailer because:

Doubles are heavier and brake response is delayed in longer air lines
Doubles are lighter
Brakes are bigger
Tractors brake better with doubles

Correct. Greater weight and longer air lines mean longer braking distance. Plan stopping distance with extra margin.

Question 20 of 20

A doubles rig is more likely to roll over than a single because:

The center of gravity is higher
The crack-the-whip effect amplifies steering input at the rear, where rollover threshold is lower
It is heavier
It is shorter

Correct. Multi-trailer rollover comes from rearward amplification — even modest steering input at the tractor becomes a violent swing at the rear trailer.

About the Vermont Doubles/Triples exam

Most states administer 20 Doubles/Triples questions and require 80% to pass. The exam emphasizes coupling and uncoupling the converter dolly, rearward amplification (the "crack-the-whip" effect), and the unique inspection and handling demands of multi-trailer rigs.

The Vermont Department of Motor Vehicles follows the federal CDL standards established by FMCSA. To earn the Doubles/Triples credential, you must answer at least 80% of the questions correctly. Many candidates score lower the first time because the test pulls from a large pool — refreshing this page will give you a different mix of questions, drawn from the same authoritative source.

Want more practice? Try the full Doubles/Triples question bank or browse all Vermont CDL practice tests.