Vermont Combination Vehicles CDL Practice Test

This is a free 20-question practice test for the Combination Vehicles portion of the Vermont Commercial Driver's License knowledge exam. Questions are pulled from a pool of 55 drawn from the AAMVA CDL Manual, which is the source document the Vermont Department of Motor Vehicles uses to write its actual exam.

How it works: Click an answer. The correct choice highlights in green, and you'll see a short explanation. Aim for 85% or better before you sit for the real test in Vermont.

Question 1 of 20

Front-trailer (lead) wheels lock and the trailer behind continues forward — this is:

Trailer jackknife
Tractor jackknife
Tire blowout
Off-tracking

Correct. When the trailer wheels lose traction and the front-of-trailer pivots while the tractor continues forward, the result is a trailer jackknife.

Question 2 of 20

During a pre-trip inspection, you should also check that the cargo:

Is loaded inside the vehicle
Is secured, balanced, within weight limits, and within size limits
Is brightly colored
Is all the same shape

Correct. Cargo securement, weight balance, and size compliance are all driver responsibilities — check before each trip.

Question 3 of 20

Combination vehicles are usually:

Easier to drive than single trucks
Harder to drive than single trucks because of length, weight, and the unique handling of articulated vehicles
The same as single trucks
Faster than single trucks

Correct. Combination vehicles (tractor-trailer rigs) are heavier, longer, and articulate at the fifth wheel — all making them more demanding than single-unit trucks.

Question 4 of 20

Most jackknifes happen because:

Drive wheels skid during braking on slippery surfaces
Brakes work too well
The road is dry
Cargo is too light

Correct. Loss of traction on the tractor drive axles during braking — typically on slick surfaces or with overly aggressive braking — causes a jackknife.

Question 5 of 20

When backing a tractor-trailer in a straight line, you should:

Let the trailer drift wherever it goes
Make small steering corrections to keep the trailer in line
Apply heavy brake pressure
Use the trailer hand valve

Correct. When backing straight, watch the trailer in your mirrors and make small steering corrections to keep it tracking straight. Big corrections lead to jackknifing.

Question 6 of 20

When approaching a curve in a tractor-trailer, you should:

Brake during the curve
Slow down before entering the curve
Speed up
Maintain steady speed

Correct. Slow before entering the curve. Once in the curve, accelerate gently to maintain stability. Braking in a curve invites trailer skid or rollover.

Question 7 of 20

The trailer hand valve should be used:

Only to test the trailer brakes; never to slow the rig in normal driving
To slow the rig in all conditions
To brake on slick roads
Continuously on long downgrades

Correct. Use the trailer hand valve only for testing trailer brakes. Using it to slow the rig can cause the trailer to skid or jackknife.

Question 8 of 20

When you connect the glad-hands, you should:

Cross-connect the red and blue lines so they cannot be confused
Connect both to the same color glad-hand
Pinch the seal first
Push them in straight without rotating

Correct. Push the glad-hands together so the rubber seals match, then rotate to lock. Be sure red goes to red and blue goes to blue (the lines themselves often cross to keep colors matched).

Question 9 of 20

When you are backing a trailer to the right, you should turn the steering wheel:

Left to start the trailer right
Right to start the trailer right
In the same direction every time
Never use the steering wheel; just push

Correct. When backing, the trailer goes opposite to the way you initially turn the steering wheel. To make the trailer go right (passenger side), start by turning the wheel left.

Question 10 of 20

When you check the fifth wheel during pre-trip, you look for:

Mounting to the frame is secure, no missing or damaged parts, no visible space between the upper and lower fifth-wheel plates, locking jaws around the kingpin shank, release arm in the locked position
Only the color
Only the bolts
Only the grease

Correct. Check mount, condition, gap, jaw engagement around kingpin shank (not the head), and release-arm lock position. Lubrication should be present but not excessive.

Question 11 of 20

The air lines connecting the tractor and trailer are:

Red (emergency) and blue (service)
Red and yellow
Blue and yellow
Black and red

Correct. The red glad-hand carries emergency/supply air; the blue glad-hand carries service air. They cross to keep matched colors when coupling.

Question 12 of 20

Before backing under a trailer to couple, you should:

Check that the trailer height is just below the fifth wheel so the fifth wheel will lift the trailer slightly when backed under
Set the trailer at any height
Lock the trailer brakes off
Disconnect the air lines

Correct. Trailer should be just low enough that the fifth wheel will lift it slightly. Too low: the fifth wheel hits the trailer body. Too high: the fifth wheel slides under without engaging the kingpin.

Question 13 of 20

To make a trailer go where you want when backing, the steering wheel should:

Be turned in the direction you want the trailer to go
Be turned opposite to the direction you want the trailer to go (then corrected)
Stay still
Be held lightly

Correct. Backing is opposite-direction steering: to swing the trailer right, turn the wheel left first, then correct as the trailer follows.

Question 14 of 20

A high-mounted trailer kingpin is dangerous because:

It will not engage the fifth wheel and the trailer can drop
It is illegal
It improves coupling
It changes color

Correct. If the trailer is too high, the fifth wheel slides under without the kingpin engaging the locking jaws. The trailer is not coupled and can drop when you pull away.

Question 15 of 20

A combination vehicle on slippery roads should be driven:

Faster to maintain control
Slower with greater following distance
At normal speed
In a higher gear

Correct. Reduce speed by at least one third on wet roads and one half on snow; double following distance on slick surfaces.

Question 16 of 20

A safe practice when arriving at a destination is to:

Pull straight in fast
Pull straight ahead, slowly, watching mirrors and clearance
Back in without help
Stop on the road

Correct. Slow approach with mirror checks gives time to identify clearance issues and pedestrians.

Question 17 of 20

A loaded trailer "bows" (sways) at speed because:

Air pressure changes
Crosswinds, road bumps, or heavy rear loading can produce trailer sway
Tires wear
Brakes are applied

Correct. Crosswinds and uneven loading can produce trailer sway. Slow down and allow the sway to dampen; do not over-correct with steering.

Question 18 of 20

A combination vehicle requires more time to stop than a single vehicle because:

It is much heavier and air must travel further to reach the trailer brakes
It accelerates faster
It is shorter
Drivers wait longer

Correct. Greater weight + brake-lag in long air lines = longer stopping distance. Plan ahead.

Question 19 of 20

A "trailer skid" happens when:

Trailer wheels lose traction and the trailer slides outward
Tractor wheels lock
Brakes overheat
Cargo shifts

Correct. When trailer wheels lose traction (often from over-application of trailer brakes alone), the trailer can slide sideways — a trailer skid or trailer swing.

Question 20 of 20

When making a right turn at an intersection in a tractor-trailer:

Swing to the left first to make room for the right turn
Make the turn from the right lane and swing wide as needed at the end of the turn
Make the turn at high speed
Stay in the left lane through the turn

Correct. Make the turn from the right lane. If you must swing wide, do so as you complete the turn, never before — swinging left first invites a vehicle to pass on your right.

About the Vermont Combination Vehicles exam

Most states administer 20 Combination Vehicles questions and require 80% to pass. The exam emphasizes the unique handling of articulated vehicles: how trailers track behind the tractor, how to prevent rollover, how to manage rearward amplification with multi-trailer combinations, and the correct sequence to couple and uncouple.

The Vermont Department of Motor Vehicles follows the federal CDL standards established by FMCSA. To earn the Combination Vehicles credential, you must answer at least 80% of the questions correctly. Many candidates score lower the first time because the test pulls from a large pool — refreshing this page will give you a different mix of questions, drawn from the same authoritative source.

Want more practice? Try the full Combination Vehicles question bank or browse all Vermont CDL practice tests.