Utah Combination Vehicles CDL Practice Test

This is a free 20-question practice test for the Combination Vehicles portion of the Utah Commercial Driver's License knowledge exam. Questions are pulled from a pool of 55 drawn from the AAMVA CDL Manual, which is the source document the Utah Driver License Division uses to write its actual exam.

How it works: Click an answer. The correct choice highlights in green, and you'll see a short explanation. Aim for 85% or better before you sit for the real test in Utah.

Question 1 of 20

The air lines connecting the tractor and trailer are:

Red (emergency) and blue (service)
Red and yellow
Blue and yellow
Black and red

Correct. The red glad-hand carries emergency/supply air; the blue glad-hand carries service air. They cross to keep matched colors when coupling.

Question 2 of 20

If the trailer is too low for coupling, you should:

Crank the trailer up with the landing gear before backing under
Skip the inspection
Drive faster
Use the trailer brake

Correct. Use the landing gear hand crank to raise the trailer to the proper height (just below fifth-wheel level) before backing under.

Question 3 of 20

A sliding fifth wheel that is unlocked or improperly secured can:

Slide unexpectedly during braking or acceleration, dangerously changing handling
Improve fuel economy
Save time
Have no effect

Correct. An unsecured sliding fifth wheel can shift during braking, changing the rig's handling unpredictably. Always verify the lock pin is engaged.

Question 4 of 20

When you cross railroad tracks in a tractor-trailer, you should:

Shift gears to maintain speed
Cross in a single gear without shifting, and never start across without room to clear the rails
Stop on the tracks if the light turns red
Honk repeatedly

Correct. Crossing in one gear (without shifting) prevents stalling on the tracks. Never enter a crossing unless you can clear it without stopping.

Question 5 of 20

A "trailer skid" happens when:

Trailer wheels lose traction and the trailer slides outward
Tractor wheels lock
Brakes overheat
Cargo shifts

Correct. When trailer wheels lose traction (often from over-application of trailer brakes alone), the trailer can slide sideways — a trailer skid or trailer swing.

Question 6 of 20

When approaching a curve in a tractor-trailer, you should:

Brake during the curve
Slow down before entering the curve
Speed up
Maintain steady speed

Correct. Slow before entering the curve. Once in the curve, accelerate gently to maintain stability. Braking in a curve invites trailer skid or rollover.

Question 7 of 20

A loaded trailer "bows" (sways) at speed because:

Air pressure changes
Crosswinds, road bumps, or heavy rear loading can produce trailer sway
Tires wear
Brakes are applied

Correct. Crosswinds and uneven loading can produce trailer sway. Slow down and allow the sway to dampen; do not over-correct with steering.

Question 8 of 20

On a tight curve or exit ramp, a tractor-trailer is most likely to roll over because:

The trailer brakes lock
The high center of gravity creates a tipping force greater than the tires can resist
The tractor accelerates
The road is dry

Correct. Centripetal forces in a curve push the cargo outward; a high center of gravity multiplies the tipping moment. Slow before the curve.

Question 9 of 20

A combination vehicle requires more time to stop than a single vehicle because:

It is much heavier and air must travel further to reach the trailer brakes
It accelerates faster
It is shorter
Drivers wait longer

Correct. Greater weight + brake-lag in long air lines = longer stopping distance. Plan ahead.

Question 10 of 20

Off-tracking refers to:

Trailer brakes overheating
Trailer wheels following a tighter path than the tractor wheels in turns
The trailer pulling left
Tires losing tread

Correct. Off-tracking is the tendency for trailer wheels to follow a smaller-radius path than the tractor wheels through a turn, more pronounced with longer wheelbases.

Question 11 of 20

A high-mounted trailer kingpin is dangerous because:

It will not engage the fifth wheel and the trailer can drop
It is illegal
It improves coupling
It changes color

Correct. If the trailer is too high, the fifth wheel slides under without the kingpin engaging the locking jaws. The trailer is not coupled and can drop when you pull away.

Question 12 of 20

Front-trailer (lead) wheels lock and the trailer behind continues forward — this is:

Trailer jackknife
Tractor jackknife
Tire blowout
Off-tracking

Correct. When the trailer wheels lose traction and the front-of-trailer pivots while the tractor continues forward, the result is a trailer jackknife.

Question 13 of 20

A combination vehicle on slippery roads should be driven:

Faster to maintain control
Slower with greater following distance
At normal speed
In a higher gear

Correct. Reduce speed by at least one third on wet roads and one half on snow; double following distance on slick surfaces.

Question 14 of 20

Most jackknifes happen because:

Drive wheels skid during braking on slippery surfaces
Brakes work too well
The road is dry
Cargo is too light

Correct. Loss of traction on the tractor drive axles during braking — typically on slick surfaces or with overly aggressive braking — causes a jackknife.

Question 15 of 20

When inspecting the kingpin during pre-trip, look for:

Excessive wear, bending, cracks, or improper lock-jaw engagement
Only the color
Only the size
Only the grease

Correct. A worn, cracked, or bent kingpin can fail under load. The locking jaws must close completely around the shank, not just the head.

Question 16 of 20

Before uncoupling, you should:

Park on level ground, set the trailer parking brake, lower the landing gear, disconnect air and electrical lines, then release the fifth-wheel jaws
Just pull away
Disconnect electrical only
Drive forward fast

Correct. Proper sequence: park level, lower landing gear to support the trailer, disconnect lines, release jaws, then pull forward slowly. Skipping any step risks dropping the trailer.

Question 17 of 20

When uncoupling, you should lower the landing gear:

After releasing the jaws
Before releasing the jaws so the trailer is supported when you pull away
Halfway
Not at all

Correct. Lower the landing gear and snug it against the ground before releasing the fifth-wheel jaws so the trailer doesn't drop when you pull away.

Question 18 of 20

On a slippery surface, drive in:

Higher gears at higher RPM
A gear that minimizes torque to the drive wheels and brake earlier and gentler
The lowest gear
Whatever is fastest

Correct. Reduce engine power to drive wheels (higher gear, gentler accelerator) and brake earlier and gentler to avoid wheel spin or skid.

Question 19 of 20

Red and amber lights on the rear of the trailer must be:

Working and visible — never broken or covered
Optional
Required only at night
Decorative only

Correct. Brake lights, turn signals, marker lights, and reflectors at the rear must be operational and clean. Damaged or non-working lights are an out-of-service item.

Question 20 of 20

When you check the fifth wheel during pre-trip, you look for:

Mounting to the frame is secure, no missing or damaged parts, no visible space between the upper and lower fifth-wheel plates, locking jaws around the kingpin shank, release arm in the locked position
Only the color
Only the bolts
Only the grease

Correct. Check mount, condition, gap, jaw engagement around kingpin shank (not the head), and release-arm lock position. Lubrication should be present but not excessive.

About the Utah Combination Vehicles exam

Most states administer 20 Combination Vehicles questions and require 80% to pass. The exam emphasizes the unique handling of articulated vehicles: how trailers track behind the tractor, how to prevent rollover, how to manage rearward amplification with multi-trailer combinations, and the correct sequence to couple and uncouple.

The Utah Driver License Division follows the federal CDL standards established by FMCSA. To earn the Combination Vehicles credential, you must answer at least 80% of the questions correctly. Many candidates score lower the first time because the test pulls from a large pool — refreshing this page will give you a different mix of questions, drawn from the same authoritative source.

Want more practice? Try the full Combination Vehicles question bank or browse all Utah CDL practice tests.