Tennessee Combination Vehicles CDL Practice Test

This is a free 20-question practice test for the Combination Vehicles portion of the Tennessee Commercial Driver's License knowledge exam. Questions are pulled from a pool of 55 drawn from the AAMVA CDL Manual, which is the source document the Tennessee Department of Safety and Homeland Security Driver Services uses to write its actual exam.

How it works: Click an answer. The correct choice highlights in green, and you'll see a short explanation. Aim for 85% or better before you sit for the real test in Tennessee.

Question 1 of 20

Cargo securement: the heaviest part of the load should be:

Loaded over the front axle area, with weight evenly distributed side to side
Loaded at the rear
Loaded on one side
Stacked on top

Correct. Loading heavy cargo to the front of the trailer over the drive axles helps with traction; loading to one side or top creates dangerous handling.

Question 2 of 20

Trailer rollover is more likely when:

Cargo is loaded low and centered
Cargo is loaded high or to one side, raising the center of gravity
Cargo is light
Trailer is empty

Correct. High cargo and uneven side-loading raise the center of gravity, increasing rollover risk on curves and ramps.

Question 3 of 20

The most likely cause of a tractor jackknife is:

Light cargo
Drive wheels lock during braking
Slow speed
Loose load

Correct. When drive wheels lose traction (locked, oversteer, ice), the tractor pivots ahead of the trailer — a jackknife.

Question 4 of 20

When approaching a curve in a tractor-trailer, you should:

Brake during the curve
Slow down before entering the curve
Speed up
Maintain steady speed

Correct. Slow before entering the curve. Once in the curve, accelerate gently to maintain stability. Braking in a curve invites trailer skid or rollover.

Question 5 of 20

When making a U-turn, a tractor-trailer needs:

Less space than a car
Substantially more space than a car — often more than a single intersection allows
The same space as a car
No turning space

Correct. Tractor-trailer turning radius is much larger than a car. A standard intersection rarely allows a U-turn — find a wider turning area.

Question 6 of 20

When backing a tractor-trailer in a straight line, you should:

Let the trailer drift wherever it goes
Make small steering corrections to keep the trailer in line
Apply heavy brake pressure
Use the trailer hand valve

Correct. When backing straight, watch the trailer in your mirrors and make small steering corrections to keep it tracking straight. Big corrections lead to jackknifing.

Question 7 of 20

When you turn on a tight radius (e.g., into a tight loading dock):

Off-tracking is exaggerated; the trailer will swing far inside the line of the tractor wheels
Off-tracking disappears
Trailer follows tractor exactly
Trailer goes wide

Correct. On a tight radius, off-tracking is more pronounced. Sweep wide enough that the trailer wheels clear curbs and obstacles.

Question 8 of 20

Before uncoupling, you should:

Park on level ground, set the trailer parking brake, lower the landing gear, disconnect air and electrical lines, then release the fifth-wheel jaws
Just pull away
Disconnect electrical only
Drive forward fast

Correct. Proper sequence: park level, lower landing gear to support the trailer, disconnect lines, release jaws, then pull forward slowly. Skipping any step risks dropping the trailer.

Question 9 of 20

Red and amber lights on the rear of the trailer must be:

Working and visible — never broken or covered
Optional
Required only at night
Decorative only

Correct. Brake lights, turn signals, marker lights, and reflectors at the rear must be operational and clean. Damaged or non-working lights are an out-of-service item.

Question 10 of 20

Off-tracking refers to:

Trailer brakes overheating
Trailer wheels following a tighter path than the tractor wheels in turns
The trailer pulling left
Tires losing tread

Correct. Off-tracking is the tendency for trailer wheels to follow a smaller-radius path than the tractor wheels through a turn, more pronounced with longer wheelbases.

Question 11 of 20

A combination vehicle requires more time to stop than a single vehicle because:

It is much heavier and air must travel further to reach the trailer brakes
It accelerates faster
It is shorter
Drivers wait longer

Correct. Greater weight + brake-lag in long air lines = longer stopping distance. Plan ahead.

Question 12 of 20

When coupling, after backing under the trailer, you should:

Pull the trailer immediately
Perform a tug test (gently pulling forward in low gear with trailer brakes set) to confirm the kingpin is locked
Disconnect the air lines
Lower the landing gear

Correct. A tug test confirms the kingpin is fully engaged. Skipping it is the leading cause of trailer drops shortly after coupling.

Question 13 of 20

A high-mounted trailer kingpin is dangerous because:

It will not engage the fifth wheel and the trailer can drop
It is illegal
It improves coupling
It changes color

Correct. If the trailer is too high, the fifth wheel slides under without the kingpin engaging the locking jaws. The trailer is not coupled and can drop when you pull away.

Question 14 of 20

When uncoupling, you should lower the landing gear:

After releasing the jaws
Before releasing the jaws so the trailer is supported when you pull away
Halfway
Not at all

Correct. Lower the landing gear and snug it against the ground before releasing the fifth-wheel jaws so the trailer doesn't drop when you pull away.

Question 15 of 20

On a tight curve or exit ramp, a tractor-trailer is most likely to roll over because:

The trailer brakes lock
The high center of gravity creates a tipping force greater than the tires can resist
The tractor accelerates
The road is dry

Correct. Centripetal forces in a curve push the cargo outward; a high center of gravity multiplies the tipping moment. Slow before the curve.

Question 16 of 20

A jackknife happens when:

The trailer wheels skid while the tractor continues forward
The tractor pulls forward in a straight line
The trailer slides sideways while the tractor pivots
The driver brakes too lightly

Correct. Jackknife is when the drive wheels skid and the trailer continues forward, causing the tractor to pivot — the rig folds at the fifth wheel like a closing knife.

Question 17 of 20

A combination vehicle on slippery roads should be driven:

Faster to maintain control
Slower with greater following distance
At normal speed
In a higher gear

Correct. Reduce speed by at least one third on wet roads and one half on snow; double following distance on slick surfaces.

Question 18 of 20

Before backing under a trailer to couple, you should:

Check that the trailer height is just below the fifth wheel so the fifth wheel will lift the trailer slightly when backed under
Set the trailer at any height
Lock the trailer brakes off
Disconnect the air lines

Correct. Trailer should be just low enough that the fifth wheel will lift it slightly. Too low: the fifth wheel hits the trailer body. Too high: the fifth wheel slides under without engaging the kingpin.

Question 19 of 20

When you check the fifth wheel during pre-trip, you look for:

Mounting to the frame is secure, no missing or damaged parts, no visible space between the upper and lower fifth-wheel plates, locking jaws around the kingpin shank, release arm in the locked position
Only the color
Only the bolts
Only the grease

Correct. Check mount, condition, gap, jaw engagement around kingpin shank (not the head), and release-arm lock position. Lubrication should be present but not excessive.

Question 20 of 20

A loaded trailer "bows" (sways) at speed because:

Air pressure changes
Crosswinds, road bumps, or heavy rear loading can produce trailer sway
Tires wear
Brakes are applied

Correct. Crosswinds and uneven loading can produce trailer sway. Slow down and allow the sway to dampen; do not over-correct with steering.

About the Tennessee Combination Vehicles exam

Most states administer 20 Combination Vehicles questions and require 80% to pass. The exam emphasizes the unique handling of articulated vehicles: how trailers track behind the tractor, how to prevent rollover, how to manage rearward amplification with multi-trailer combinations, and the correct sequence to couple and uncouple.

The Tennessee Department of Safety and Homeland Security Driver Services follows the federal CDL standards established by FMCSA. To earn the Combination Vehicles credential, you must answer at least 80% of the questions correctly. Many candidates score lower the first time because the test pulls from a large pool — refreshing this page will give you a different mix of questions, drawn from the same authoritative source.

Want more practice? Try the full Combination Vehicles question bank or browse all Tennessee CDL practice tests.