Tennessee Air Brakes CDL Practice Test

This is a free 20-question practice test for the Air Brakes portion of the Tennessee Commercial Driver's License knowledge exam. Questions are pulled from a pool of 71 drawn from the AAMVA CDL Manual, which is the source document the Tennessee Department of Safety and Homeland Security Driver Services uses to write its actual exam.

How it works: Click an answer. The correct choice highlights in green, and you'll see a short explanation. Aim for 85% or better before you sit for the real test in Tennessee.

Question 1 of 20

A condition called "brake fade" is most likely on:

Long downgrades
Flat highway
Backing into a dock
Fueling

Correct. Brake fade comes from heat from extended use — most commonly on long, steep downgrades where the brakes are working continuously.

Question 2 of 20

For a single vehicle (not a combination) with engine off and brakes released, the maximum allowable air-loss rate is:

1 psi/min
2 psi/min
3 psi/min
4 psi/min

Correct. A single vehicle is allowed no more than 2 psi/min of air loss with engine off and brakes released.

Question 3 of 20

Slack adjusters need to be checked because:

They wear and require adjustment to maintain braking force
They never need attention
They are decorative
They affect only the parking brake

Correct. Slack adjusters control how far the pushrod must travel to apply the brake. Out-of-adjustment slack adjusters are the leading mechanical cause of out-of-service violations.

Question 4 of 20

For a single vehicle with engine off and brakes applied, the maximum allowable air-loss rate is:

1 psi/min
2 psi/min
3 psi/min
4 psi/min

Correct. A single vehicle is allowed no more than 3 psi/min with brakes fully applied.

Question 5 of 20

When brake drums or shoes get very hot, you should:

Park immediately
Continue driving
Pull over and let them cool, but do not apply the parking brake until they have cooled
Throw water on them

Correct. Park where you can let the brakes cool. Do not apply the parking (spring) brake on overheated brakes — it can damage them or cause warpage.

Question 6 of 20

When checking the brakes on a downgrade, you should:

Use the air-pressure gauge to monitor brake-system pressure for excessive use
Pump the pedal
Drive faster
Ignore the gauge

Correct. Watch the air-pressure gauge. If pressure drops faster than the compressor can recover, brakes are being used too aggressively for the gear selection.

Question 7 of 20

Air tanks must be drained because:

They get heavy
Compressor oil and water can collect inside, contaminating the brake system
They expire
It is required after every trip

Correct. Water and compressor oil collect at the bottom of air tanks. They must be drained to keep the system clean and prevent winter freeze-ups.

Question 8 of 20

Pre-trip air-brake check (Step 1) is to:

Test the parking brake
Test the air leakage rate
Time the air-pressure build-up
Check the slack adjusters

Correct. In the seven-step air-brake check the first step is testing the parking brake — release service brakes, set parking brake, gently try to move the vehicle in low gear.

Question 9 of 20

The "brake-system warning device" must come on no later than:

10 psi
30 psi
60 psi
100 psi

Correct. A federal-rule low-air-pressure warning device must activate at or before 60 psi.

Question 10 of 20

The supply pressure gauges show:

The brake-pedal pressure
The pressure in the air storage tanks
The amount of air being used by the brakes
The trailer brake pressure only

Correct. The supply (primary and secondary) pressure gauges show air pressure available for braking — a critical reading before driving and during operation.

Question 11 of 20

The parking-brake control:

Is a yellow diamond-shaped knob
Is a red round knob
Is a green knob
Does not exist on modern trucks

Correct. The parking-brake control is a yellow diamond-shaped knob, distinct from the red round trailer-supply knob.

Question 12 of 20

If you must drive a vehicle with manual front-wheel-brake limiting valve, you should keep it in the "normal" position:

Always
Only on slick roads
In the slippery position only
Only when empty

Correct. Keep the front-wheel limiting valve in the "normal" position. Modern trucks rarely have this valve, but if equipped, leaving it in "slippery" reduces front braking and lengthens stopping distance.

Question 13 of 20

You should never leave the vehicle unattended without:

Locking the doors
Applying the parking brakes and chocking the wheels if necessary
Turning off the radio
Removing the key

Correct. Set the parking brake. On grades or where unintended movement could occur, chock the wheels in addition.

Question 14 of 20

After connecting the trailer air lines, you should:

Drive away
Charge the trailer air system, check that the trailer brakes work, and inspect glad-hand connections
Lock the trailer brakes
Turn off the supply

Correct. Charge the trailer system, then test the trailer brakes by pulling out the trailer-supply knob to make sure they hold the trailer.

Question 15 of 20

The parts of an air-brake system include:

Air compressor, governor, air storage tanks, foot valve, and brake chambers
Master cylinder, brake fluid, and calipers
Hydraulic pump, lines, and disc rotors
Vacuum booster and reservoir

Correct. Air-brake systems use a compressor, governor, storage tanks, foot valve, and brake chambers — distinct from hydraulic systems used in cars.

Question 16 of 20

In a dual air-brake system, the time required for air pressure to build from 85 to 100 psi should be no more than:

15 seconds
30 seconds
45 seconds
120 seconds

Correct. In dual air-brake systems, air should build from 85 to 100 psi within 45 seconds at engine governed RPM.

Question 17 of 20

Air storage tanks are used to:

Carry coolant
Hold compressed air for use by the brakes
Store fuel
House the alternator

Correct. Air storage (or "supply") tanks hold compressed air ready for brake application. Trucks have multiple tanks for redundancy.

Question 18 of 20

If a trailer breaks away, the emergency brakes on the trailer will be applied because:

The driver pulled the parking brake
The air supply to the trailer is interrupted, releasing the spring brakes on the trailer
The trailer wiring shuts down
The trailer ABS engages

Correct. When the air line breaks (or is disconnected), trailer air pressure drops and the trailer spring brakes apply, stopping the trailer.

Question 19 of 20

Brake fade is the result of:

Cold brakes
Worn linings only
Heat from continuous use, which reduces braking effectiveness
Air leaks

Correct. Brake fade comes from heat. Manage downgrade speed by gear selection plus intermittent firm brake use, not continuous light pressure.

Question 20 of 20

Wet brakes:

Improve braking
Cause reduced power, brake pulling, or wheel lockup
Have no effect
Are normal in winter

Correct. After fording water, brakes may be wet. Drive slowly while applying light brake pressure to dry them.

About the Tennessee Air Brakes exam

States typically administer 25 Air Brakes questions and require 80% to pass. Questions cover air-brake system parts, dual systems, supply pressure, brake-system warning, slack adjusters, the parking brake, the spring brake, the pre-trip air-system check, and the proper way to perform a leakage-rate test.

The Tennessee Department of Safety and Homeland Security Driver Services follows the federal CDL standards established by FMCSA. To earn the Air Brakes credential, you must answer at least 80% of the questions correctly. Many candidates score lower the first time because the test pulls from a large pool — refreshing this page will give you a different mix of questions, drawn from the same authoritative source.

Want more practice? Try the full Air Brakes question bank or browse all Tennessee CDL practice tests.