Pennsylvania Combination Vehicles CDL Practice Test

This is a free 20-question practice test for the Combination Vehicles portion of the Pennsylvania Commercial Driver's License knowledge exam. Questions are pulled from a pool of 55 drawn from the AAMVA CDL Manual, which is the source document the Pennsylvania Department of Transportation Driver Licensing uses to write its actual exam.

How it works: Click an answer. The correct choice highlights in green, and you'll see a short explanation. Aim for 85% or better before you sit for the real test in Pennsylvania.

Question 1 of 20

When you supply air to the trailer for the first time after coupling, you should:

Wait until air pressure builds in the trailer reservoir, then test the trailer brakes by pulling out the trailer-supply knob
Drive away immediately
Disconnect the lines
Skip the test

Correct. Charge the trailer system. Then test the trailer brake function by tugging gently or pulling the trailer-supply knob to confirm trailer brakes apply.

Question 2 of 20

Your trailer ABS warning lamp is on. The trailer service brakes:

Will not work at all
Still work normally — only ABS function is unavailable
Lock up
Apply automatically

Correct. Trailer service brakes still work normally without ABS. Have the system repaired; ABS gives extra control during emergency braking.

Question 3 of 20

A jackknife happens when:

The trailer wheels skid while the tractor continues forward
The tractor pulls forward in a straight line
The trailer slides sideways while the tractor pivots
The driver brakes too lightly

Correct. Jackknife is when the drive wheels skid and the trailer continues forward, causing the tractor to pivot — the rig folds at the fifth wheel like a closing knife.

Question 4 of 20

When approaching a curve in a tractor-trailer, you should:

Brake during the curve
Slow down before entering the curve
Speed up
Maintain steady speed

Correct. Slow before entering the curve. Once in the curve, accelerate gently to maintain stability. Braking in a curve invites trailer skid or rollover.

Question 5 of 20

When you check the fifth wheel during pre-trip, you look for:

Mounting to the frame is secure, no missing or damaged parts, no visible space between the upper and lower fifth-wheel plates, locking jaws around the kingpin shank, release arm in the locked position
Only the color
Only the bolts
Only the grease

Correct. Check mount, condition, gap, jaw engagement around kingpin shank (not the head), and release-arm lock position. Lubrication should be present but not excessive.

Question 6 of 20

When inspecting the kingpin during pre-trip, look for:

Excessive wear, bending, cracks, or improper lock-jaw engagement
Only the color
Only the size
Only the grease

Correct. A worn, cracked, or bent kingpin can fail under load. The locking jaws must close completely around the shank, not just the head.

Question 7 of 20

A trailer that has been sitting may have:

Brakes that need careful adjustment, rust on the kingpin, or other issues that should be inspected
No issues — trailers are static
Built-in safety
Better brakes

Correct. Trailers idle for long periods can develop brake corrosion, kingpin rust, low tires, and other issues. Inspect carefully before use.

Question 8 of 20

To make a trailer go where you want when backing, the steering wheel should:

Be turned in the direction you want the trailer to go
Be turned opposite to the direction you want the trailer to go (then corrected)
Stay still
Be held lightly

Correct. Backing is opposite-direction steering: to swing the trailer right, turn the wheel left first, then correct as the trailer follows.

Question 9 of 20

A "trailer skid" happens when:

Trailer wheels lose traction and the trailer slides outward
Tractor wheels lock
Brakes overheat
Cargo shifts

Correct. When trailer wheels lose traction (often from over-application of trailer brakes alone), the trailer can slide sideways — a trailer skid or trailer swing.

Question 10 of 20

The trailer hand valve should be used:

Only to test the trailer brakes; never to slow the rig in normal driving
To slow the rig in all conditions
To brake on slick roads
Continuously on long downgrades

Correct. Use the trailer hand valve only for testing trailer brakes. Using it to slow the rig can cause the trailer to skid or jackknife.

Question 11 of 20

When coupling, after backing under the trailer, you should:

Pull the trailer immediately
Perform a tug test (gently pulling forward in low gear with trailer brakes set) to confirm the kingpin is locked
Disconnect the air lines
Lower the landing gear

Correct. A tug test confirms the kingpin is fully engaged. Skipping it is the leading cause of trailer drops shortly after coupling.

Question 12 of 20

A safe practice when arriving at a destination is to:

Pull straight in fast
Pull straight ahead, slowly, watching mirrors and clearance
Back in without help
Stop on the road

Correct. Slow approach with mirror checks gives time to identify clearance issues and pedestrians.

Question 13 of 20

Off-tracking refers to:

Trailer brakes overheating
Trailer wheels following a tighter path than the tractor wheels in turns
The trailer pulling left
Tires losing tread

Correct. Off-tracking is the tendency for trailer wheels to follow a smaller-radius path than the tractor wheels through a turn, more pronounced with longer wheelbases.

Question 14 of 20

Cargo securement: the heaviest part of the load should be:

Loaded over the front axle area, with weight evenly distributed side to side
Loaded at the rear
Loaded on one side
Stacked on top

Correct. Loading heavy cargo to the front of the trailer over the drive axles helps with traction; loading to one side or top creates dangerous handling.

Question 15 of 20

Red and amber lights on the rear of the trailer must be:

Working and visible — never broken or covered
Optional
Required only at night
Decorative only

Correct. Brake lights, turn signals, marker lights, and reflectors at the rear must be operational and clean. Damaged or non-working lights are an out-of-service item.

Question 16 of 20

A sliding-tandem trailer allows you to:

Adjust the trailer-axle position to redistribute weight between trailer axles and tractor drive axles
Speed up
Cool the load
Steer the trailer

Correct. Sliding tandems shift trailer axles forward (more weight on tractor) or aft (more weight on trailer axles), helping meet axle-weight limits.

Question 17 of 20

Before backing under a trailer to couple, you should:

Check that the trailer height is just below the fifth wheel so the fifth wheel will lift the trailer slightly when backed under
Set the trailer at any height
Lock the trailer brakes off
Disconnect the air lines

Correct. Trailer should be just low enough that the fifth wheel will lift it slightly. Too low: the fifth wheel hits the trailer body. Too high: the fifth wheel slides under without engaging the kingpin.

Question 18 of 20

On a tight curve or exit ramp, a tractor-trailer is most likely to roll over because:

The trailer brakes lock
The high center of gravity creates a tipping force greater than the tires can resist
The tractor accelerates
The road is dry

Correct. Centripetal forces in a curve push the cargo outward; a high center of gravity multiplies the tipping moment. Slow before the curve.

Question 19 of 20

The "rearward amplification" effect:

Is greatest in the lead trailer
Is greatest in the rear-most trailer of doubles or triples
Does not exist
Is the same in every trailer

Correct. Rearward amplification — the crack-the-whip effect — is most severe in the rear trailer of a multi-trailer combination.

Question 20 of 20

A sliding fifth wheel allows you to:

Adjust the weight distribution between drive axles and trailer axles
Speed up
Slow down
Disable the trailer brakes

Correct. Sliding fifth wheels move forward to put more weight on drive axles or aft to reduce drive-axle weight, helping comply with axle-weight limits.

About the Pennsylvania Combination Vehicles exam

Most states administer 20 Combination Vehicles questions and require 80% to pass. The exam emphasizes the unique handling of articulated vehicles: how trailers track behind the tractor, how to prevent rollover, how to manage rearward amplification with multi-trailer combinations, and the correct sequence to couple and uncouple.

The Pennsylvania Department of Transportation Driver Licensing follows the federal CDL standards established by FMCSA. To earn the Combination Vehicles credential, you must answer at least 80% of the questions correctly. Many candidates score lower the first time because the test pulls from a large pool — refreshing this page will give you a different mix of questions, drawn from the same authoritative source.

Want more practice? Try the full Combination Vehicles question bank or browse all Pennsylvania CDL practice tests.