New York Combination Vehicles CDL Practice Test

This is a free 20-question practice test for the Combination Vehicles portion of the New York Commercial Driver's License knowledge exam. Questions are pulled from a pool of 55 drawn from the AAMVA CDL Manual, which is the source document the New York State Department of Motor Vehicles uses to write its actual exam.

How it works: Click an answer. The correct choice highlights in green, and you'll see a short explanation. Aim for 85% or better before you sit for the real test in New York.

Question 1 of 20

Before backing under a trailer to couple, you should:

Check that the trailer height is just below the fifth wheel so the fifth wheel will lift the trailer slightly when backed under
Set the trailer at any height
Lock the trailer brakes off
Disconnect the air lines

Correct. Trailer should be just low enough that the fifth wheel will lift it slightly. Too low: the fifth wheel hits the trailer body. Too high: the fifth wheel slides under without engaging the kingpin.

Question 2 of 20

When approaching a curve in a tractor-trailer, you should:

Brake during the curve
Slow down before entering the curve
Speed up
Maintain steady speed

Correct. Slow before entering the curve. Once in the curve, accelerate gently to maintain stability. Braking in a curve invites trailer skid or rollover.

Question 3 of 20

When inspecting the kingpin during pre-trip, look for:

Excessive wear, bending, cracks, or improper lock-jaw engagement
Only the color
Only the size
Only the grease

Correct. A worn, cracked, or bent kingpin can fail under load. The locking jaws must close completely around the shank, not just the head.

Question 4 of 20

When you connect the glad-hands, you should:

Cross-connect the red and blue lines so they cannot be confused
Connect both to the same color glad-hand
Pinch the seal first
Push them in straight without rotating

Correct. Push the glad-hands together so the rubber seals match, then rotate to lock. Be sure red goes to red and blue goes to blue (the lines themselves often cross to keep colors matched).

Question 5 of 20

The most likely cause of a tractor jackknife is:

Light cargo
Drive wheels lock during braking
Slow speed
Loose load

Correct. When drive wheels lose traction (locked, oversteer, ice), the tractor pivots ahead of the trailer — a jackknife.

Question 6 of 20

Before uncoupling, you should:

Park on level ground, set the trailer parking brake, lower the landing gear, disconnect air and electrical lines, then release the fifth-wheel jaws
Just pull away
Disconnect electrical only
Drive forward fast

Correct. Proper sequence: park level, lower landing gear to support the trailer, disconnect lines, release jaws, then pull forward slowly. Skipping any step risks dropping the trailer.

Question 7 of 20

Combination vehicles are usually:

Easier to drive than single trucks
Harder to drive than single trucks because of length, weight, and the unique handling of articulated vehicles
The same as single trucks
Faster than single trucks

Correct. Combination vehicles (tractor-trailer rigs) are heavier, longer, and articulate at the fifth wheel — all making them more demanding than single-unit trucks.

Question 8 of 20

A jackknife happens when:

The trailer wheels skid while the tractor continues forward
The tractor pulls forward in a straight line
The trailer slides sideways while the tractor pivots
The driver brakes too lightly

Correct. Jackknife is when the drive wheels skid and the trailer continues forward, causing the tractor to pivot — the rig folds at the fifth wheel like a closing knife.

Question 9 of 20

When you check the fifth wheel during pre-trip, you look for:

Mounting to the frame is secure, no missing or damaged parts, no visible space between the upper and lower fifth-wheel plates, locking jaws around the kingpin shank, release arm in the locked position
Only the color
Only the bolts
Only the grease

Correct. Check mount, condition, gap, jaw engagement around kingpin shank (not the head), and release-arm lock position. Lubrication should be present but not excessive.

Question 10 of 20

A loaded trailer "bows" (sways) at speed because:

Air pressure changes
Crosswinds, road bumps, or heavy rear loading can produce trailer sway
Tires wear
Brakes are applied

Correct. Crosswinds and uneven loading can produce trailer sway. Slow down and allow the sway to dampen; do not over-correct with steering.

Question 11 of 20

Off-tracking refers to:

Trailer brakes overheating
Trailer wheels following a tighter path than the tractor wheels in turns
The trailer pulling left
Tires losing tread

Correct. Off-tracking is the tendency for trailer wheels to follow a smaller-radius path than the tractor wheels through a turn, more pronounced with longer wheelbases.

Question 12 of 20

A combination vehicle on slippery roads should be driven:

Faster to maintain control
Slower with greater following distance
At normal speed
In a higher gear

Correct. Reduce speed by at least one third on wet roads and one half on snow; double following distance on slick surfaces.

Question 13 of 20

The trailer hand valve should be used:

Only to test the trailer brakes; never to slow the rig in normal driving
To slow the rig in all conditions
To brake on slick roads
Continuously on long downgrades

Correct. Use the trailer hand valve only for testing trailer brakes. Using it to slow the rig can cause the trailer to skid or jackknife.

Question 14 of 20

The air lines connecting the tractor and trailer are:

Red (emergency) and blue (service)
Red and yellow
Blue and yellow
Black and red

Correct. The red glad-hand carries emergency/supply air; the blue glad-hand carries service air. They cross to keep matched colors when coupling.

Question 15 of 20

When coupling, after backing under the trailer, you should:

Pull the trailer immediately
Perform a tug test (gently pulling forward in low gear with trailer brakes set) to confirm the kingpin is locked
Disconnect the air lines
Lower the landing gear

Correct. A tug test confirms the kingpin is fully engaged. Skipping it is the leading cause of trailer drops shortly after coupling.

Question 16 of 20

When you couple, the locking jaws of the fifth wheel must close around:

The kingpin shank, not just the head
Just the head
The trailer skirt
The wheel

Correct. The locking jaws must engage the kingpin shank below the head. If the jaws close above the head, the connection is unsafe.

Question 17 of 20

When you supply air to the trailer for the first time after coupling, you should:

Wait until air pressure builds in the trailer reservoir, then test the trailer brakes by pulling out the trailer-supply knob
Drive away immediately
Disconnect the lines
Skip the test

Correct. Charge the trailer system. Then test the trailer brake function by tugging gently or pulling the trailer-supply knob to confirm trailer brakes apply.

Question 18 of 20

To make a trailer go where you want when backing, the steering wheel should:

Be turned in the direction you want the trailer to go
Be turned opposite to the direction you want the trailer to go (then corrected)
Stay still
Be held lightly

Correct. Backing is opposite-direction steering: to swing the trailer right, turn the wheel left first, then correct as the trailer follows.

Question 19 of 20

A trailer that has been sitting may have:

Brakes that need careful adjustment, rust on the kingpin, or other issues that should be inspected
No issues — trailers are static
Built-in safety
Better brakes

Correct. Trailers idle for long periods can develop brake corrosion, kingpin rust, low tires, and other issues. Inspect carefully before use.

Question 20 of 20

A "trailer skid" happens when:

Trailer wheels lose traction and the trailer slides outward
Tractor wheels lock
Brakes overheat
Cargo shifts

Correct. When trailer wheels lose traction (often from over-application of trailer brakes alone), the trailer can slide sideways — a trailer skid or trailer swing.

About the New York Combination Vehicles exam

Most states administer 20 Combination Vehicles questions and require 80% to pass. The exam emphasizes the unique handling of articulated vehicles: how trailers track behind the tractor, how to prevent rollover, how to manage rearward amplification with multi-trailer combinations, and the correct sequence to couple and uncouple.

The New York State Department of Motor Vehicles follows the federal CDL standards established by FMCSA. To earn the Combination Vehicles credential, you must answer at least 80% of the questions correctly. Many candidates score lower the first time because the test pulls from a large pool — refreshing this page will give you a different mix of questions, drawn from the same authoritative source.

Want more practice? Try the full Combination Vehicles question bank or browse all New York CDL practice tests.