New Hampshire Air Brakes CDL Practice Test

This is a free 20-question practice test for the Air Brakes portion of the New Hampshire Commercial Driver's License knowledge exam. Questions are pulled from a pool of 71 drawn from the AAMVA CDL Manual, which is the source document the New Hampshire Division of Motor Vehicles uses to write its actual exam.

How it works: Click an answer. The correct choice highlights in green, and you'll see a short explanation. Aim for 85% or better before you sit for the real test in New Hampshire.

Question 1 of 20

After connecting the trailer air lines, you should:

Drive away
Charge the trailer air system, check that the trailer brakes work, and inspect glad-hand connections
Lock the trailer brakes
Turn off the supply

Correct. Charge the trailer system, then test the trailer brakes by pulling out the trailer-supply knob to make sure they hold the trailer.

Question 2 of 20

The S-cam:

Is a type of fuel pump
Forces the brake shoes against the drum to provide braking action
Adjusts the slack adjuster
Is the parking-brake control

Correct. When the foot valve is pressed, air pushes the brake-chamber pushrod, which moves the slack adjuster, which rotates the S-cam shaft, forcing the shoes against the drum.

Question 3 of 20

The spring brakes:

Are held off by air pressure and apply automatically when pressure drops
Are activated only by the foot valve
Are activated only by the trailer hand valve
Are not used in modern trucks

Correct. Spring brakes use heavy springs that apply the brake when air pressure is released or drops below 20-45 psi — they serve as both parking and emergency brake.

Question 4 of 20

The trailer air-supply control:

Is a yellow diamond knob
Is a red eight-sided (octagonal) knob
Is a green knob
Is the same knob as the parking brake

Correct. The trailer air-supply (tractor protection) is a red eight-sided knob. Push in to supply air to the trailer; pull out to shut off air.

Question 5 of 20

When should you use the trailer hand valve to slow the rig?

Whenever you want trailer-only braking
Never; using the trailer hand valve alone can cause a trailer skid
Always when going downhill
Only on dry pavement

Correct. Using the trailer hand valve alone applies brakes only at the trailer wheels and can cause the trailer to lock up and skid. Always use the foot valve to brake.

Question 6 of 20

You hear a steady "ssss" sound while parked with the engine off. This is most likely:

Normal venting
An air leak that needs immediate attention
The compressor running
Trailer brakes releasing

Correct. A steady hiss with the engine off indicates an air leak — find and repair before driving.

Question 7 of 20

Air-brake disc brakes use:

Air to apply force to a clamp on a rotating disc, instead of a drum
Hydraulic fluid
A separate fuel system
Spring force only

Correct. Disc brakes use a brake chamber and slack adjuster like S-cam drum brakes, but the force closes a caliper on a rotor instead of forcing shoes against a drum.

Question 8 of 20

In a dual air-brake system, the time required for air pressure to build from 85 to 100 psi should be no more than:

15 seconds
30 seconds
45 seconds
120 seconds

Correct. In dual air-brake systems, air should build from 85 to 100 psi within 45 seconds at engine governed RPM.

Question 9 of 20

A long downgrade requires:

Riding the brakes the whole way
Selecting a low gear before starting down and using intermittent firm brake applications
Coasting in neutral
Using the engine brake only

Correct. Pick a low gear before starting down. Use the brakes in firm, intermittent applications: brake to 5 mph below safe speed, release, repeat.

Question 10 of 20

When should you NOT use the parking brakes?

When the vehicle is parked
When the brakes are very hot, such as after a long downgrade — they could damage if applied
At any time
When the engine is off

Correct. Hot brakes can be damaged by the spring brakes contracting against hot drums. Let the brakes cool before parking.

Question 11 of 20

When the spring brakes apply automatically as air pressure drops, this typically happens between:

100 and 120 psi
60 and 80 psi
20 and 45 psi
5 and 10 psi

Correct. Spring brakes will fully apply somewhere between 20 and 45 psi as system pressure drops, depending on the vehicle.

Question 12 of 20

Modulating valves on the trailer:

Don't exist
Apply increasing brake pressure as you push the foot valve harder
Are emergency-only
Open the parking brake

Correct. The trailer service brakes are modulated — pressing harder on the foot valve produces more brake-chamber pressure at the trailer.

Question 13 of 20

The "brake-system warning device" must come on no later than:

10 psi
30 psi
60 psi
100 psi

Correct. A federal-rule low-air-pressure warning device must activate at or before 60 psi.

Question 14 of 20

In an emergency stop on a non-ABS vehicle, you should:

Apply the brakes lightly
Use stab braking — full brake until wheels lock, release, repeat
Pump the brakes rapidly
Apply only the trailer hand valve

Correct. Stab braking applies brakes hard until the wheels lock, then releases when you feel skid — this slows the vehicle while keeping it straight.

Question 15 of 20

A low-air-pressure warning device must come on at or before:

20 psi
40 psi
60 psi
80 psi

Correct. A federal-mandated low-air-pressure warning (light, buzzer, or wig-wag) must activate at or before 60 psi.

Question 16 of 20

Air-brake adjustment is critical because out-of-adjustment brakes:

Reduce stopping power and can cause failure on long downgrades
Improve fuel economy
Have no effect
Require less air pressure

Correct. Out-of-adjustment slack adjusters reduce braking force at the wheel, increasing stopping distance and risking brake failure on long downgrades.

Question 17 of 20

A condition called "brake fade" is most likely on:

Long downgrades
Flat highway
Backing into a dock
Fueling

Correct. Brake fade comes from heat from extended use — most commonly on long, steep downgrades where the brakes are working continuously.

Question 18 of 20

The brake-system warning light or buzzer is designed to alert you when:

The brakes are working
Air pressure has dropped below the level needed to brake safely
Brake fluid is low
You haven't serviced the brakes recently

Correct. The brake-system warning device alerts you to dangerous low air pressure — typically activating at or before 60 psi.

Question 19 of 20

In a fully charged dual air-brake system at idle, you should test the low-pressure warning by:

Letting the air bleed down with the engine off and brakes off, fanning the brakes if needed; warning should activate at or before 60 psi
Holding the foot valve down for one minute
Removing the alternator belt
Disconnecting the compressor

Correct. Engine off, fan the brake pedal to bleed pressure. The low-pressure warning device should activate before pressure drops below 60 psi.

Question 20 of 20

For a combination vehicle (tractor and trailer) with engine off and brakes released, the maximum allowable air-loss rate is:

2 psi/min
3 psi/min
4 psi/min
6 psi/min

Correct. A combination vehicle is allowed no more than 3 psi/min with brakes released, or 4 psi/min with brakes applied.

About the New Hampshire Air Brakes exam

States typically administer 25 Air Brakes questions and require 80% to pass. Questions cover air-brake system parts, dual systems, supply pressure, brake-system warning, slack adjusters, the parking brake, the spring brake, the pre-trip air-system check, and the proper way to perform a leakage-rate test.

The New Hampshire Division of Motor Vehicles follows the federal CDL standards established by FMCSA. To earn the Air Brakes credential, you must answer at least 80% of the questions correctly. Many candidates score lower the first time because the test pulls from a large pool — refreshing this page will give you a different mix of questions, drawn from the same authoritative source.

Want more practice? Try the full Air Brakes question bank or browse all New Hampshire CDL practice tests.