Minnesota Air Brakes CDL Practice Test

This is a free 20-question practice test for the Air Brakes portion of the Minnesota Commercial Driver's License knowledge exam. Questions are pulled from a pool of 71 drawn from the AAMVA CDL Manual, which is the source document the Minnesota Driver and Vehicle Services uses to write its actual exam.

How it works: Click an answer. The correct choice highlights in green, and you'll see a short explanation. Aim for 85% or better before you sit for the real test in Minnesota.

Question 1 of 20

The spring brakes:

Are held off by air pressure and apply automatically when pressure drops
Are activated only by the foot valve
Are activated only by the trailer hand valve
Are not used in modern trucks

Correct. Spring brakes use heavy springs that apply the brake when air pressure is released or drops below 20-45 psi — they serve as both parking and emergency brake.

Question 2 of 20

After connecting the trailer air lines, you should:

Drive away
Charge the trailer air system, check that the trailer brakes work, and inspect glad-hand connections
Lock the trailer brakes
Turn off the supply

Correct. Charge the trailer system, then test the trailer brakes by pulling out the trailer-supply knob to make sure they hold the trailer.

Question 3 of 20

The trailer air-supply control:

Is a yellow diamond knob
Is a red eight-sided (octagonal) knob
Is a green knob
Is the same knob as the parking brake

Correct. The trailer air-supply (tractor protection) is a red eight-sided knob. Push in to supply air to the trailer; pull out to shut off air.

Question 4 of 20

For a single vehicle (not a combination) with engine off and brakes released, the maximum allowable air-loss rate is:

1 psi/min
2 psi/min
3 psi/min
4 psi/min

Correct. A single vehicle is allowed no more than 2 psi/min of air loss with engine off and brakes released.

Question 5 of 20

Air tanks must be drained because:

They get heavy
Compressor oil and water can collect inside, contaminating the brake system
They expire
It is required after every trip

Correct. Water and compressor oil collect at the bottom of air tanks. They must be drained to keep the system clean and prevent winter freeze-ups.

Question 6 of 20

Slack adjusters need to be checked because:

They wear and require adjustment to maintain braking force
They never need attention
They are decorative
They affect only the parking brake

Correct. Slack adjusters control how far the pushrod must travel to apply the brake. Out-of-adjustment slack adjusters are the leading mechanical cause of out-of-service violations.

Question 7 of 20

A "wet tank" is:

Where most water collects in the air system, which must be drained regularly
The trailer brake reservoir
The cooling-system reservoir
The fuel tank

Correct. The first storage tank — sometimes called the wet tank or supply tank — is where water and oil from the compressor collect. Drain it daily.

Question 8 of 20

Wet brakes:

Improve braking
Cause reduced power, brake pulling, or wheel lockup
Have no effect
Are normal in winter

Correct. After fording water, brakes may be wet. Drive slowly while applying light brake pressure to dry them.

Question 9 of 20

The application pressure gauge shows:

The pressure in the storage tanks
How much pressure is being applied to the brakes when you press the foot valve
Tire pressure
Engine oil pressure

Correct. The application gauge (when present) shows brake-application pressure — useful for spotting brake-system problems on long downgrades.

Question 10 of 20

When checking the brakes on a downgrade, you should:

Use the air-pressure gauge to monitor brake-system pressure for excessive use
Pump the pedal
Drive faster
Ignore the gauge

Correct. Watch the air-pressure gauge. If pressure drops faster than the compressor can recover, brakes are being used too aggressively for the gear selection.

Question 11 of 20

You should drain the air tanks:

Once a month
Once a year
At the end of every working day
Never

Correct. Drain all air tanks at the end of each working day to remove water and compressor oil that has condensed in the tanks.

Question 12 of 20

The parking-brake control:

Is a yellow diamond-shaped knob
Is a red round knob
Is a green knob
Does not exist on modern trucks

Correct. The parking-brake control is a yellow diamond-shaped knob, distinct from the red round trailer-supply knob.

Question 13 of 20

A condition called "brake fade" is most likely on:

Long downgrades
Flat highway
Backing into a dock
Fueling

Correct. Brake fade comes from heat from extended use — most commonly on long, steep downgrades where the brakes are working continuously.

Question 14 of 20

Air loss from the brake system on a moving combination vehicle, with brakes applied, should not exceed:

2 psi/min
3 psi/min
4 psi/min
6 psi/min

Correct. Combination vehicle, brakes applied, engine off: no more than 4 psi/min air loss. Engine off, brakes released: no more than 3 psi/min.

Question 15 of 20

For a single vehicle with engine off and brakes applied, the maximum allowable air-loss rate is:

1 psi/min
2 psi/min
3 psi/min
4 psi/min

Correct. A single vehicle is allowed no more than 3 psi/min with brakes fully applied.

Question 16 of 20

The governor controls:

Engine RPM
When the air compressor pumps air into the air storage tanks
Brake-pedal travel
Trailer hand-valve operation

Correct. The governor cycles the compressor: it cuts the compressor in around 100 psi and cuts it out around 125 psi.

Question 17 of 20

Pre-trip air-brake check (Step 1) is to:

Test the parking brake
Test the air leakage rate
Time the air-pressure build-up
Check the slack adjusters

Correct. In the seven-step air-brake check the first step is testing the parking brake — release service brakes, set parking brake, gently try to move the vehicle in low gear.

Question 18 of 20

You should never use the parking brake when the brakes are very hot because:

It will not hold
It can damage the brakes or cause warpage
It will release on its own
It will use too much air

Correct. Hot brakes cooled with parking brake applied can warp the drum or rotor, or cause the spring brake to fail to release.

Question 19 of 20

The parts of an air-brake system include:

Air compressor, governor, air storage tanks, foot valve, and brake chambers
Master cylinder, brake fluid, and calipers
Hydraulic pump, lines, and disc rotors
Vacuum booster and reservoir

Correct. Air-brake systems use a compressor, governor, storage tanks, foot valve, and brake chambers — distinct from hydraulic systems used in cars.

Question 20 of 20

When should you use the trailer hand valve to slow the rig?

Whenever you want trailer-only braking
Never; using the trailer hand valve alone can cause a trailer skid
Always when going downhill
Only on dry pavement

Correct. Using the trailer hand valve alone applies brakes only at the trailer wheels and can cause the trailer to lock up and skid. Always use the foot valve to brake.

About the Minnesota Air Brakes exam

States typically administer 25 Air Brakes questions and require 80% to pass. Questions cover air-brake system parts, dual systems, supply pressure, brake-system warning, slack adjusters, the parking brake, the spring brake, the pre-trip air-system check, and the proper way to perform a leakage-rate test.

The Minnesota Driver and Vehicle Services follows the federal CDL standards established by FMCSA. To earn the Air Brakes credential, you must answer at least 80% of the questions correctly. Many candidates score lower the first time because the test pulls from a large pool — refreshing this page will give you a different mix of questions, drawn from the same authoritative source.

Want more practice? Try the full Air Brakes question bank or browse all Minnesota CDL practice tests.