Massachusetts Combination Vehicles CDL Practice Test

This is a free 20-question practice test for the Combination Vehicles portion of the Massachusetts Commercial Driver's License knowledge exam. Questions are pulled from a pool of 55 drawn from the AAMVA CDL Manual, which is the source document the Massachusetts Registry of Motor Vehicles uses to write its actual exam.

How it works: Click an answer. The correct choice highlights in green, and you'll see a short explanation. Aim for 85% or better before you sit for the real test in Massachusetts.

Question 1 of 20

A jackknife happens when:

The trailer wheels skid while the tractor continues forward
The tractor pulls forward in a straight line
The trailer slides sideways while the tractor pivots
The driver brakes too lightly

Correct. Jackknife is when the drive wheels skid and the trailer continues forward, causing the tractor to pivot — the rig folds at the fifth wheel like a closing knife.

Question 2 of 20

The trailer hand valve should be used:

Only to test the trailer brakes; never to slow the rig in normal driving
To slow the rig in all conditions
To brake on slick roads
Continuously on long downgrades

Correct. Use the trailer hand valve only for testing trailer brakes. Using it to slow the rig can cause the trailer to skid or jackknife.

Question 3 of 20

When backing a tractor-trailer in a straight line, you should:

Let the trailer drift wherever it goes
Make small steering corrections to keep the trailer in line
Apply heavy brake pressure
Use the trailer hand valve

Correct. When backing straight, watch the trailer in your mirrors and make small steering corrections to keep it tracking straight. Big corrections lead to jackknifing.

Question 4 of 20

Before uncoupling, you should:

Park on level ground, set the trailer parking brake, lower the landing gear, disconnect air and electrical lines, then release the fifth-wheel jaws
Just pull away
Disconnect electrical only
Drive forward fast

Correct. Proper sequence: park level, lower landing gear to support the trailer, disconnect lines, release jaws, then pull forward slowly. Skipping any step risks dropping the trailer.

Question 5 of 20

A combination-vehicle pre-trip should include:

All single-vehicle items plus fifth wheel, kingpin, sliding fifth wheel/sliding tandem locks, mud flaps, trailer brakes, lights, and trailer tires
Only the tractor
Only the trailer
Only the cargo

Correct. You inspect the entire rig — tractor + trailer + connections + cargo securement — not just the tractor.

Question 6 of 20

Length and weight increase what about a combination vehicle?

Stopping distance, off-tracking, blind spots, and time required for lane changes
Visibility
Speed
Acceleration

Correct. Longer, heavier rigs need more stopping distance, swing wider in turns, have larger blind spots, and require more time and space to change lanes.

Question 7 of 20

Cargo securement: the heaviest part of the load should be:

Loaded over the front axle area, with weight evenly distributed side to side
Loaded at the rear
Loaded on one side
Stacked on top

Correct. Loading heavy cargo to the front of the trailer over the drive axles helps with traction; loading to one side or top creates dangerous handling.

Question 8 of 20

When you are backing a trailer to the right, you should turn the steering wheel:

Left to start the trailer right
Right to start the trailer right
In the same direction every time
Never use the steering wheel; just push

Correct. When backing, the trailer goes opposite to the way you initially turn the steering wheel. To make the trailer go right (passenger side), start by turning the wheel left.

Question 9 of 20

A combination vehicle on slippery roads should be driven:

Faster to maintain control
Slower with greater following distance
At normal speed
In a higher gear

Correct. Reduce speed by at least one third on wet roads and one half on snow; double following distance on slick surfaces.

Question 10 of 20

A sliding-tandem trailer allows you to:

Adjust the trailer-axle position to redistribute weight between trailer axles and tractor drive axles
Speed up
Cool the load
Steer the trailer

Correct. Sliding tandems shift trailer axles forward (more weight on tractor) or aft (more weight on trailer axles), helping meet axle-weight limits.

Question 11 of 20

When approaching a curve in a tractor-trailer, you should:

Brake during the curve
Slow down before entering the curve
Speed up
Maintain steady speed

Correct. Slow before entering the curve. Once in the curve, accelerate gently to maintain stability. Braking in a curve invites trailer skid or rollover.

Question 12 of 20

When making a turn, you should signal:

Just before the turn
Well in advance — at least 100 feet for a turn at low speed
Only if other vehicles are present
At the start of the turn

Correct. Signal early enough that other drivers see and process the signal — generally at least 100 feet before in town, longer at highway speeds.

Question 13 of 20

Before backing under a trailer to couple, you should:

Check that the trailer height is just below the fifth wheel so the fifth wheel will lift the trailer slightly when backed under
Set the trailer at any height
Lock the trailer brakes off
Disconnect the air lines

Correct. Trailer should be just low enough that the fifth wheel will lift it slightly. Too low: the fifth wheel hits the trailer body. Too high: the fifth wheel slides under without engaging the kingpin.

Question 14 of 20

A loaded trailer "bows" (sways) at speed because:

Air pressure changes
Crosswinds, road bumps, or heavy rear loading can produce trailer sway
Tires wear
Brakes are applied

Correct. Crosswinds and uneven loading can produce trailer sway. Slow down and allow the sway to dampen; do not over-correct with steering.

Question 15 of 20

A combination vehicle requires more time to stop than a single vehicle because:

It is much heavier and air must travel further to reach the trailer brakes
It accelerates faster
It is shorter
Drivers wait longer

Correct. Greater weight + brake-lag in long air lines = longer stopping distance. Plan ahead.

Question 16 of 20

When uncoupling, you should lower the landing gear:

After releasing the jaws
Before releasing the jaws so the trailer is supported when you pull away
Halfway
Not at all

Correct. Lower the landing gear and snug it against the ground before releasing the fifth-wheel jaws so the trailer doesn't drop when you pull away.

Question 17 of 20

Which is the proper following distance for a 60-foot rig at 50 mph?

3 seconds
6 seconds
7 seconds
12 seconds

Correct. 1 second per 10 feet at speeds below 40 mph, plus 1 extra second above 40. 60 feet = 6 seconds + 1 = 7 seconds at highway speed.

Question 18 of 20

A sliding fifth wheel allows you to:

Adjust the weight distribution between drive axles and trailer axles
Speed up
Slow down
Disable the trailer brakes

Correct. Sliding fifth wheels move forward to put more weight on drive axles or aft to reduce drive-axle weight, helping comply with axle-weight limits.

Question 19 of 20

To make a trailer go where you want when backing, the steering wheel should:

Be turned in the direction you want the trailer to go
Be turned opposite to the direction you want the trailer to go (then corrected)
Stay still
Be held lightly

Correct. Backing is opposite-direction steering: to swing the trailer right, turn the wheel left first, then correct as the trailer follows.

Question 20 of 20

A sliding fifth wheel that is unlocked or improperly secured can:

Slide unexpectedly during braking or acceleration, dangerously changing handling
Improve fuel economy
Save time
Have no effect

Correct. An unsecured sliding fifth wheel can shift during braking, changing the rig's handling unpredictably. Always verify the lock pin is engaged.

About the Massachusetts Combination Vehicles exam

Most states administer 20 Combination Vehicles questions and require 80% to pass. The exam emphasizes the unique handling of articulated vehicles: how trailers track behind the tractor, how to prevent rollover, how to manage rearward amplification with multi-trailer combinations, and the correct sequence to couple and uncouple.

The Massachusetts Registry of Motor Vehicles follows the federal CDL standards established by FMCSA. To earn the Combination Vehicles credential, you must answer at least 80% of the questions correctly. Many candidates score lower the first time because the test pulls from a large pool — refreshing this page will give you a different mix of questions, drawn from the same authoritative source.

Want more practice? Try the full Combination Vehicles question bank or browse all Massachusetts CDL practice tests.