Maryland Combination Vehicles CDL Practice Test

This is a free 20-question practice test for the Combination Vehicles portion of the Maryland Commercial Driver's License knowledge exam. Questions are pulled from a pool of 55 drawn from the AAMVA CDL Manual, which is the source document the Maryland Motor Vehicle Administration uses to write its actual exam.

How it works: Click an answer. The correct choice highlights in green, and you'll see a short explanation. Aim for 85% or better before you sit for the real test in Maryland.

Question 1 of 20

Before backing under a trailer to couple, you should:

Check that the trailer height is just below the fifth wheel so the fifth wheel will lift the trailer slightly when backed under
Set the trailer at any height
Lock the trailer brakes off
Disconnect the air lines

Correct. Trailer should be just low enough that the fifth wheel will lift it slightly. Too low: the fifth wheel hits the trailer body. Too high: the fifth wheel slides under without engaging the kingpin.

Question 2 of 20

A "trailer skid" happens when:

Trailer wheels lose traction and the trailer slides outward
Tractor wheels lock
Brakes overheat
Cargo shifts

Correct. When trailer wheels lose traction (often from over-application of trailer brakes alone), the trailer can slide sideways — a trailer skid or trailer swing.

Question 3 of 20

A jackknife happens when:

The trailer wheels skid while the tractor continues forward
The tractor pulls forward in a straight line
The trailer slides sideways while the tractor pivots
The driver brakes too lightly

Correct. Jackknife is when the drive wheels skid and the trailer continues forward, causing the tractor to pivot — the rig folds at the fifth wheel like a closing knife.

Question 4 of 20

When you supply air to the trailer for the first time after coupling, you should:

Wait until air pressure builds in the trailer reservoir, then test the trailer brakes by pulling out the trailer-supply knob
Drive away immediately
Disconnect the lines
Skip the test

Correct. Charge the trailer system. Then test the trailer brake function by tugging gently or pulling the trailer-supply knob to confirm trailer brakes apply.

Question 5 of 20

A combination-vehicle pre-trip should include:

All single-vehicle items plus fifth wheel, kingpin, sliding fifth wheel/sliding tandem locks, mud flaps, trailer brakes, lights, and trailer tires
Only the tractor
Only the trailer
Only the cargo

Correct. You inspect the entire rig — tractor + trailer + connections + cargo securement — not just the tractor.

Question 6 of 20

When making a right turn at an intersection in a tractor-trailer:

Swing to the left first to make room for the right turn
Make the turn from the right lane and swing wide as needed at the end of the turn
Make the turn at high speed
Stay in the left lane through the turn

Correct. Make the turn from the right lane. If you must swing wide, do so as you complete the turn, never before — swinging left first invites a vehicle to pass on your right.

Question 7 of 20

Trailer rollover is more likely when:

Cargo is loaded low and centered
Cargo is loaded high or to one side, raising the center of gravity
Cargo is light
Trailer is empty

Correct. High cargo and uneven side-loading raise the center of gravity, increasing rollover risk on curves and ramps.

Question 8 of 20

On a tight curve or exit ramp, a tractor-trailer is most likely to roll over because:

The trailer brakes lock
The high center of gravity creates a tipping force greater than the tires can resist
The tractor accelerates
The road is dry

Correct. Centripetal forces in a curve push the cargo outward; a high center of gravity multiplies the tipping moment. Slow before the curve.

Question 9 of 20

Length and weight increase what about a combination vehicle?

Stopping distance, off-tracking, blind spots, and time required for lane changes
Visibility
Speed
Acceleration

Correct. Longer, heavier rigs need more stopping distance, swing wider in turns, have larger blind spots, and require more time and space to change lanes.

Question 10 of 20

Before uncoupling, you should:

Park on level ground, set the trailer parking brake, lower the landing gear, disconnect air and electrical lines, then release the fifth-wheel jaws
Just pull away
Disconnect electrical only
Drive forward fast

Correct. Proper sequence: park level, lower landing gear to support the trailer, disconnect lines, release jaws, then pull forward slowly. Skipping any step risks dropping the trailer.

Question 11 of 20

A safe practice when arriving at a destination is to:

Pull straight in fast
Pull straight ahead, slowly, watching mirrors and clearance
Back in without help
Stop on the road

Correct. Slow approach with mirror checks gives time to identify clearance issues and pedestrians.

Question 12 of 20

When approaching a curve in a tractor-trailer, you should:

Brake during the curve
Slow down before entering the curve
Speed up
Maintain steady speed

Correct. Slow before entering the curve. Once in the curve, accelerate gently to maintain stability. Braking in a curve invites trailer skid or rollover.

Question 13 of 20

The "rearward amplification" effect:

Is greatest in the lead trailer
Is greatest in the rear-most trailer of doubles or triples
Does not exist
Is the same in every trailer

Correct. Rearward amplification — the crack-the-whip effect — is most severe in the rear trailer of a multi-trailer combination.

Question 14 of 20

A sliding-tandem trailer allows you to:

Adjust the trailer-axle position to redistribute weight between trailer axles and tractor drive axles
Speed up
Cool the load
Steer the trailer

Correct. Sliding tandems shift trailer axles forward (more weight on tractor) or aft (more weight on trailer axles), helping meet axle-weight limits.

Question 15 of 20

When making a U-turn, a tractor-trailer needs:

Less space than a car
Substantially more space than a car — often more than a single intersection allows
The same space as a car
No turning space

Correct. Tractor-trailer turning radius is much larger than a car. A standard intersection rarely allows a U-turn — find a wider turning area.

Question 16 of 20

A trailer that has been sitting may have:

Brakes that need careful adjustment, rust on the kingpin, or other issues that should be inspected
No issues — trailers are static
Built-in safety
Better brakes

Correct. Trailers idle for long periods can develop brake corrosion, kingpin rust, low tires, and other issues. Inspect carefully before use.

Question 17 of 20

When you check the fifth wheel during pre-trip, you look for:

Mounting to the frame is secure, no missing or damaged parts, no visible space between the upper and lower fifth-wheel plates, locking jaws around the kingpin shank, release arm in the locked position
Only the color
Only the bolts
Only the grease

Correct. Check mount, condition, gap, jaw engagement around kingpin shank (not the head), and release-arm lock position. Lubrication should be present but not excessive.

Question 18 of 20

To make a trailer go where you want when backing, the steering wheel should:

Be turned in the direction you want the trailer to go
Be turned opposite to the direction you want the trailer to go (then corrected)
Stay still
Be held lightly

Correct. Backing is opposite-direction steering: to swing the trailer right, turn the wheel left first, then correct as the trailer follows.

Question 19 of 20

Red and amber lights on the rear of the trailer must be:

Working and visible — never broken or covered
Optional
Required only at night
Decorative only

Correct. Brake lights, turn signals, marker lights, and reflectors at the rear must be operational and clean. Damaged or non-working lights are an out-of-service item.

Question 20 of 20

Combination vehicles are usually:

Easier to drive than single trucks
Harder to drive than single trucks because of length, weight, and the unique handling of articulated vehicles
The same as single trucks
Faster than single trucks

Correct. Combination vehicles (tractor-trailer rigs) are heavier, longer, and articulate at the fifth wheel — all making them more demanding than single-unit trucks.

About the Maryland Combination Vehicles exam

Most states administer 20 Combination Vehicles questions and require 80% to pass. The exam emphasizes the unique handling of articulated vehicles: how trailers track behind the tractor, how to prevent rollover, how to manage rearward amplification with multi-trailer combinations, and the correct sequence to couple and uncouple.

The Maryland Motor Vehicle Administration follows the federal CDL standards established by FMCSA. To earn the Combination Vehicles credential, you must answer at least 80% of the questions correctly. Many candidates score lower the first time because the test pulls from a large pool — refreshing this page will give you a different mix of questions, drawn from the same authoritative source.

Want more practice? Try the full Combination Vehicles question bank or browse all Maryland CDL practice tests.