Idaho Doubles/Triples CDL Practice Test

This is a free 20-question practice test for the Doubles/Triples portion of the Idaho Commercial Driver's License knowledge exam. Questions are pulled from a pool of 50 drawn from the AAMVA CDL Manual, which is the source document the Idaho Transportation Department Division of Motor Vehicles uses to write its actual exam.

How it works: Click an answer. The correct choice highlights in green, and you'll see a short explanation. Aim for 85% or better before you sit for the real test in Idaho.

Question 1 of 20

A converter dolly is:

A small hand truck
A set of axles with a fifth wheel that converts a semi-trailer into a full trailer for use in doubles/triples
A trailer-loading device
A type of brake

Correct. A converter dolly has a small frame, axle(s), and a fifth wheel mounted on top — it transforms a semi-trailer into a full trailer behind another trailer.

Question 2 of 20

Crosswinds are particularly hazardous for:

Empty doubles and triples
Loaded singles
Backing
Slow speeds

Correct. Empty trailers in a multi-trailer rig present a large flat surface to crosswinds — a strong gust can blow the rear trailer over.

Question 3 of 20

Air pressure on a triple-trailer rig takes:

Less time to reach the rear trailer than on a single
Significantly more time to reach the rear trailer's brake chambers
The same time
No air pressure is needed

Correct. Each additional trailer adds line length. Brake response at the rear trailer of a triple is noticeably delayed — brake earlier.

Question 4 of 20

A driver licensed for Class A with all endorsements may drive any combination vehicle. The T endorsement allows:

Doubles and triples
Hazmat
Tanker
Buses

Correct. T endorsement specifically authorizes doubles and triples. Other endorsements (H, N, P, S) cover other categories.

Question 5 of 20

When inspecting a doubles or triples rig, you should additionally check:

Each pintle hook, each set of safety chains, each converter dolly, each trailer's lights, brake chamber connections, glad-hands, and shut-off valves
Only the lead trailer
Only the tractor
Only the cargo

Correct. Every connection point and every trailer needs inspection — pintle hooks, chains, dollies, lights, brake lines, glad-hands, and air-supply valves.

Question 6 of 20

An empty rear trailer on a multi-trailer rig:

Is more likely to roll over in evasive steering than a loaded one
Is always stable
Cannot roll over
Has no effect

Correct. Lighter trailer = more vulnerable to crack-the-whip and crosswinds. Empty rear trailers in multi-trailer rigs roll easily.

Question 7 of 20

When you uncouple a converter dolly, you should:

Disconnect air and electrical, secure or remove safety chains, then release the pintle hook
Just yank it off
Drive forward fast
Use only the trailer brake

Correct. Park level, disconnect air and electric, lower trailer landing gear if applicable, remove safety chains, then release the pintle hook to free the dolly.

Question 8 of 20

When testing the brakes on a doubles rig:

Do all the standard checks plus verify air pressure builds at the rear trailer and that brakes apply at all wheels
Only test the tractor
Only test the lead trailer
Skip the test

Correct. Test the entire rig: build-up time, leakage, low-pressure warning, parking brake, and confirm rear-trailer brake function.

Question 9 of 20

Crosswinds may cause the rear trailer of a doubles to:

Sway dangerously, especially when empty
Brake automatically
Steer itself
Have no effect

Correct. Empty trailers act as sails. Strong crosswinds can sway or even tip an empty rear trailer. Reduce speed in high winds.

Question 10 of 20

Triples are restricted in many states. You should:

Drive triples anywhere
Verify state-by-state legality before crossing into a state
Use a special placard
Avoid driving in cities

Correct. Many states restrict triples to specific routes (turnpikes, designated corridors). Verify legality and route before crossing into a state.

Question 11 of 20

When you encounter a breakaway in your doubles (a trailer separates):

Maintain control of the tractor and lead trailer, brake gently to a controlled stop, set warning devices, and contact dispatch
Brake hard
Speed up
Swerve sharply

Correct. Maintain control of what remains, brake gently and progressively, secure the area with warning devices, contact dispatch.

Question 12 of 20

Driving doubles or triples on the highway:

Requires gentler steering, longer following distance, and earlier braking
Allows the same maneuvers as a single trailer
Allows higher cornering speeds
Has no special concerns

Correct. Multi-trailer rigs are more sensitive to abrupt steering, take longer to brake, and amplify any movement to the rear. Be gentle and plan ahead.

Question 13 of 20

On a steep downgrade with doubles, you should:

Select a lower gear before starting down and use intermittent firm braking
Coast in neutral
Use only trailer brake
Stay in high gear

Correct. Same rule as any combination vehicle, but plan extra margin: doubles take longer to stop and the rear trailer may push.

Question 14 of 20

A pintle hook is:

The hitch on the rear of a trailer used to tow another trailer or dolly
The kingpin
The fifth wheel
A type of placard

Correct. The pintle hook is the strong rear-mounted hitch that grips the dolly's lunette eye, allowing one trailer to tow another behind it.

Question 15 of 20

A "drive-axle skid" on a doubles rig:

Can lead to a tractor jackknife and complicated trailer movement behind it
Is harmless
Means the dolly broke
Increases stability

Correct. A drive-axle skid leads to tractor jackknife. With trailers behind, the situation gets worse fast — the rear trailers can swing wildly.

Question 16 of 20

A "set of triples" typically refers to:

One tractor pulling three trailers
Three trailers without a tractor
Three tractors and one trailer
Three tractors only

Correct. A set of triples is one tractor pulling three trailers — usually allowed only on specific designated routes.

Question 17 of 20

The "T" endorsement is required to:

Drive any commercial vehicle
Pull two or more trailers
Drive a bus
Haul hazmat

Correct. The T endorsement is required to pull more than one trailer (doubles or triples).

Question 18 of 20

Before connecting a converter dolly, you should:

Inspect tires, brakes, fifth-wheel jaws, and overall condition
Skip inspection
Only check the tires
Only check the lights

Correct. Pre-trip the dolly: tires, brake adjustment, fifth-wheel jaws (open and clean), pintle hook, electrical receptacle, lights.

Question 19 of 20

When inspecting a converter dolly, the pintle hook must:

Lock fully closed around the lunette eye
Be loose
Be cracked
Be replaced quarterly

Correct. The pintle hook must close fully around the lunette eye, with no excessive wear or cracks. Add safety chains as backup.

Question 20 of 20

A safe practice when starting from a stop with doubles:

Accelerate gently to avoid breakaway sway in the second trailer
Floor the accelerator
Use only the trailer hand valve
Skip first gear

Correct. Sudden acceleration can cause the rear trailer to sway. Start gently in low gear.

About the Idaho Doubles/Triples exam

Most states administer 20 Doubles/Triples questions and require 80% to pass. The exam emphasizes coupling and uncoupling the converter dolly, rearward amplification (the "crack-the-whip" effect), and the unique inspection and handling demands of multi-trailer rigs.

The Idaho Transportation Department Division of Motor Vehicles follows the federal CDL standards established by FMCSA. To earn the Doubles/Triples credential, you must answer at least 80% of the questions correctly. Many candidates score lower the first time because the test pulls from a large pool — refreshing this page will give you a different mix of questions, drawn from the same authoritative source.

Want more practice? Try the full Doubles/Triples question bank or browse all Idaho CDL practice tests.