District of Columbia Combination Vehicles CDL Practice Test

This is a free 20-question practice test for the Combination Vehicles portion of the District of Columbia Commercial Driver's License knowledge exam. Questions are pulled from a pool of 55 drawn from the AAMVA CDL Manual, which is the source document the District of Columbia Department of Motor Vehicles uses to write its actual exam.

How it works: Click an answer. The correct choice highlights in green, and you'll see a short explanation. Aim for 85% or better before you sit for the real test in District of Columbia.

Question 1 of 20

When you turn on a tight radius (e.g., into a tight loading dock):

Off-tracking is exaggerated; the trailer will swing far inside the line of the tractor wheels
Off-tracking disappears
Trailer follows tractor exactly
Trailer goes wide

Correct. On a tight radius, off-tracking is more pronounced. Sweep wide enough that the trailer wheels clear curbs and obstacles.

Question 2 of 20

On a tight curve or exit ramp, a tractor-trailer is most likely to roll over because:

The trailer brakes lock
The high center of gravity creates a tipping force greater than the tires can resist
The tractor accelerates
The road is dry

Correct. Centripetal forces in a curve push the cargo outward; a high center of gravity multiplies the tipping moment. Slow before the curve.

Question 3 of 20

A jackknife happens when:

The trailer wheels skid while the tractor continues forward
The tractor pulls forward in a straight line
The trailer slides sideways while the tractor pivots
The driver brakes too lightly

Correct. Jackknife is when the drive wheels skid and the trailer continues forward, causing the tractor to pivot — the rig folds at the fifth wheel like a closing knife.

Question 4 of 20

When inspecting the kingpin during pre-trip, look for:

Excessive wear, bending, cracks, or improper lock-jaw engagement
Only the color
Only the size
Only the grease

Correct. A worn, cracked, or bent kingpin can fail under load. The locking jaws must close completely around the shank, not just the head.

Question 5 of 20

The most likely cause of a tractor jackknife is:

Light cargo
Drive wheels lock during braking
Slow speed
Loose load

Correct. When drive wheels lose traction (locked, oversteer, ice), the tractor pivots ahead of the trailer — a jackknife.

Question 6 of 20

Before backing under a trailer to couple, you should:

Check that the trailer height is just below the fifth wheel so the fifth wheel will lift the trailer slightly when backed under
Set the trailer at any height
Lock the trailer brakes off
Disconnect the air lines

Correct. Trailer should be just low enough that the fifth wheel will lift it slightly. Too low: the fifth wheel hits the trailer body. Too high: the fifth wheel slides under without engaging the kingpin.

Question 7 of 20

A combination vehicle requires more time to stop than a single vehicle because:

It is much heavier and air must travel further to reach the trailer brakes
It accelerates faster
It is shorter
Drivers wait longer

Correct. Greater weight + brake-lag in long air lines = longer stopping distance. Plan ahead.

Question 8 of 20

Trailer rollover is more likely when:

Cargo is loaded low and centered
Cargo is loaded high or to one side, raising the center of gravity
Cargo is light
Trailer is empty

Correct. High cargo and uneven side-loading raise the center of gravity, increasing rollover risk on curves and ramps.

Question 9 of 20

When you supply air to the trailer for the first time after coupling, you should:

Wait until air pressure builds in the trailer reservoir, then test the trailer brakes by pulling out the trailer-supply knob
Drive away immediately
Disconnect the lines
Skip the test

Correct. Charge the trailer system. Then test the trailer brake function by tugging gently or pulling the trailer-supply knob to confirm trailer brakes apply.

Question 10 of 20

When approaching a curve in a tractor-trailer, you should:

Brake during the curve
Slow down before entering the curve
Speed up
Maintain steady speed

Correct. Slow before entering the curve. Once in the curve, accelerate gently to maintain stability. Braking in a curve invites trailer skid or rollover.

Question 11 of 20

Front-trailer (lead) wheels lock and the trailer behind continues forward — this is:

Trailer jackknife
Tractor jackknife
Tire blowout
Off-tracking

Correct. When the trailer wheels lose traction and the front-of-trailer pivots while the tractor continues forward, the result is a trailer jackknife.

Question 12 of 20

After connecting the trailer, before pulling away, you should always:

Visually inspect the fifth-wheel/kingpin connection from outside the cab
Just trust the gauge
Honk the horn
Set the trailer brake

Correct. Always visually confirm: no gap between fifth wheel and trailer plate, jaws closed around the kingpin shank, locking lever fully in place.

Question 13 of 20

A loaded trailer "bows" (sways) at speed because:

Air pressure changes
Crosswinds, road bumps, or heavy rear loading can produce trailer sway
Tires wear
Brakes are applied

Correct. Crosswinds and uneven loading can produce trailer sway. Slow down and allow the sway to dampen; do not over-correct with steering.

Question 14 of 20

A combination vehicle on slippery roads should be driven:

Faster to maintain control
Slower with greater following distance
At normal speed
In a higher gear

Correct. Reduce speed by at least one third on wet roads and one half on snow; double following distance on slick surfaces.

Question 15 of 20

When coupling, after backing under the trailer, you should:

Pull the trailer immediately
Perform a tug test (gently pulling forward in low gear with trailer brakes set) to confirm the kingpin is locked
Disconnect the air lines
Lower the landing gear

Correct. A tug test confirms the kingpin is fully engaged. Skipping it is the leading cause of trailer drops shortly after coupling.

Question 16 of 20

A sliding fifth wheel allows you to:

Adjust the weight distribution between drive axles and trailer axles
Speed up
Slow down
Disable the trailer brakes

Correct. Sliding fifth wheels move forward to put more weight on drive axles or aft to reduce drive-axle weight, helping comply with axle-weight limits.

Question 17 of 20

When making a right turn at an intersection in a tractor-trailer:

Swing to the left first to make room for the right turn
Make the turn from the right lane and swing wide as needed at the end of the turn
Make the turn at high speed
Stay in the left lane through the turn

Correct. Make the turn from the right lane. If you must swing wide, do so as you complete the turn, never before — swinging left first invites a vehicle to pass on your right.

Question 18 of 20

A sliding-tandem trailer allows you to:

Adjust the trailer-axle position to redistribute weight between trailer axles and tractor drive axles
Speed up
Cool the load
Steer the trailer

Correct. Sliding tandems shift trailer axles forward (more weight on tractor) or aft (more weight on trailer axles), helping meet axle-weight limits.

Question 19 of 20

When you cross railroad tracks in a tractor-trailer, you should:

Shift gears to maintain speed
Cross in a single gear without shifting, and never start across without room to clear the rails
Stop on the tracks if the light turns red
Honk repeatedly

Correct. Crossing in one gear (without shifting) prevents stalling on the tracks. Never enter a crossing unless you can clear it without stopping.

Question 20 of 20

Cargo securement: the heaviest part of the load should be:

Loaded over the front axle area, with weight evenly distributed side to side
Loaded at the rear
Loaded on one side
Stacked on top

Correct. Loading heavy cargo to the front of the trailer over the drive axles helps with traction; loading to one side or top creates dangerous handling.

About the District of Columbia Combination Vehicles exam

Most states administer 20 Combination Vehicles questions and require 80% to pass. The exam emphasizes the unique handling of articulated vehicles: how trailers track behind the tractor, how to prevent rollover, how to manage rearward amplification with multi-trailer combinations, and the correct sequence to couple and uncouple.

The District of Columbia Department of Motor Vehicles follows the federal CDL standards established by FMCSA. To earn the Combination Vehicles credential, you must answer at least 80% of the questions correctly. Many candidates score lower the first time because the test pulls from a large pool — refreshing this page will give you a different mix of questions, drawn from the same authoritative source.

Want more practice? Try the full Combination Vehicles question bank or browse all District of Columbia CDL practice tests.