Connecticut Air Brakes CDL Practice Test

This is a free 20-question practice test for the Air Brakes portion of the Connecticut Commercial Driver's License knowledge exam. Questions are pulled from a pool of 71 drawn from the AAMVA CDL Manual, which is the source document the Connecticut Department of Motor Vehicles uses to write its actual exam.

How it works: Click an answer. The correct choice highlights in green, and you'll see a short explanation. Aim for 85% or better before you sit for the real test in Connecticut.

Question 1 of 20

When you make a normal stop with air brakes, you should:

Push the brake pedal down hard
Apply firm steady pressure to slow you smoothly
Pump the brakes
Use only the trailer brake

Correct. For normal stops, apply steady firm pressure on the foot valve and adjust to maintain a smooth stop.

Question 2 of 20

The brake-system warning light or buzzer is designed to alert you when:

The brakes are working
Air pressure has dropped below the level needed to brake safely
Brake fluid is low
You haven't serviced the brakes recently

Correct. The brake-system warning device alerts you to dangerous low air pressure — typically activating at or before 60 psi.

Question 3 of 20

Air storage tanks are used to:

Carry coolant
Hold compressed air for use by the brakes
Store fuel
House the alternator

Correct. Air storage (or "supply") tanks hold compressed air ready for brake application. Trucks have multiple tanks for redundancy.

Question 4 of 20

Slack adjusters need to be checked because:

They wear and require adjustment to maintain braking force
They never need attention
They are decorative
They affect only the parking brake

Correct. Slack adjusters control how far the pushrod must travel to apply the brake. Out-of-adjustment slack adjusters are the leading mechanical cause of out-of-service violations.

Question 5 of 20

A long downgrade requires:

Riding the brakes the whole way
Selecting a low gear before starting down and using intermittent firm brake applications
Coasting in neutral
Using the engine brake only

Correct. Pick a low gear before starting down. Use the brakes in firm, intermittent applications: brake to 5 mph below safe speed, release, repeat.

Question 6 of 20

Air brakes take longer to work than hydraulic brakes because:

Air takes longer to flow than fluid
Air-brake lines are longer than hydraulic lines and have more components
Drivers wait longer to brake
Air brakes are simpler

Correct. Brake-lag in air systems comes from the time air takes to travel through lines and reach all the brake chambers — typically 0.4 seconds added to perception/reaction time.

Question 7 of 20

The application pressure gauge shows:

The pressure in the storage tanks
How much pressure is being applied to the brakes when you press the foot valve
Tire pressure
Engine oil pressure

Correct. The application gauge (when present) shows brake-application pressure — useful for spotting brake-system problems on long downgrades.

Question 8 of 20

When should you use the trailer hand valve to slow the rig?

Whenever you want trailer-only braking
Never; using the trailer hand valve alone can cause a trailer skid
Always when going downhill
Only on dry pavement

Correct. Using the trailer hand valve alone applies brakes only at the trailer wheels and can cause the trailer to lock up and skid. Always use the foot valve to brake.

Question 9 of 20

The trailer air-supply control:

Is a yellow diamond knob
Is a red eight-sided (octagonal) knob
Is a green knob
Is the same knob as the parking brake

Correct. The trailer air-supply (tractor protection) is a red eight-sided knob. Push in to supply air to the trailer; pull out to shut off air.

Question 10 of 20

In a dual air-brake system, you should let the air pressure build to at least what level before driving?

60 psi
80 psi
100 psi
125 psi

Correct. Wait until the system pressure is at least 100 psi before driving in a dual air-brake system.

Question 11 of 20

You hear a steady "ssss" sound while parked with the engine off. This is most likely:

Normal venting
An air leak that needs immediate attention
The compressor running
Trailer brakes releasing

Correct. A steady hiss with the engine off indicates an air leak — find and repair before driving.

Question 12 of 20

You should perform a static air-leakage test by:

Driving and watching the gauge
With the engine off, brakes released, watching air pressure for one minute
With the engine running at high RPM
By tapping the air tank with a wrench

Correct. Engine off, brakes released, fully charged system: watch for air loss over one minute. Then apply brakes and check again.

Question 13 of 20

For a single vehicle with engine off and brakes applied, the maximum allowable air-loss rate is:

1 psi/min
2 psi/min
3 psi/min
4 psi/min

Correct. A single vehicle is allowed no more than 3 psi/min with brakes fully applied.

Question 14 of 20

Continuous use of the brakes on a long downgrade can cause:

Improved braking
Brake fade — loss of braking effectiveness due to overheating
No effect
Faster wear of the air compressor

Correct. Holding the brakes overheats them and causes brake fade — drums expand and brake compounds lose effectiveness, reducing braking force.

Question 15 of 20

A condition called "brake fade" is most likely on:

Long downgrades
Flat highway
Backing into a dock
Fueling

Correct. Brake fade comes from heat from extended use — most commonly on long, steep downgrades where the brakes are working continuously.

Question 16 of 20

When the spring brakes apply automatically as air pressure drops, this typically happens between:

100 and 120 psi
60 and 80 psi
20 and 45 psi
5 and 10 psi

Correct. Spring brakes will fully apply somewhere between 20 and 45 psi as system pressure drops, depending on the vehicle.

Question 17 of 20

After connecting the trailer air lines, you should:

Drive away
Charge the trailer air system, check that the trailer brakes work, and inspect glad-hand connections
Lock the trailer brakes
Turn off the supply

Correct. Charge the trailer system, then test the trailer brakes by pulling out the trailer-supply knob to make sure they hold the trailer.

Question 18 of 20

In a dual air-brake system, the time required for air pressure to build from 85 to 100 psi should be no more than:

15 seconds
30 seconds
45 seconds
120 seconds

Correct. In dual air-brake systems, air should build from 85 to 100 psi within 45 seconds at engine governed RPM.

Question 19 of 20

Brake fade is the result of:

Cold brakes
Worn linings only
Heat from continuous use, which reduces braking effectiveness
Air leaks

Correct. Brake fade comes from heat. Manage downgrade speed by gear selection plus intermittent firm brake use, not continuous light pressure.

Question 20 of 20

When releasing brakes after a hard stop, you should:

Continue holding the brakes
Release smoothly to allow air to refill the tanks
Pump the brakes
Apply the parking brake immediately

Correct. Release the brakes smoothly. Air tanks refill while you drive; allow the compressor to recharge the system before the next braking event.

About the Connecticut Air Brakes exam

States typically administer 25 Air Brakes questions and require 80% to pass. Questions cover air-brake system parts, dual systems, supply pressure, brake-system warning, slack adjusters, the parking brake, the spring brake, the pre-trip air-system check, and the proper way to perform a leakage-rate test.

The Connecticut Department of Motor Vehicles follows the federal CDL standards established by FMCSA. To earn the Air Brakes credential, you must answer at least 80% of the questions correctly. Many candidates score lower the first time because the test pulls from a large pool — refreshing this page will give you a different mix of questions, drawn from the same authoritative source.

Want more practice? Try the full Air Brakes question bank or browse all Connecticut CDL practice tests.