California Air Brakes CDL Practice Test

This is a free 20-question practice test for the Air Brakes portion of the California Commercial Driver's License knowledge exam. Questions are pulled from a pool of 71 drawn from the AAMVA CDL Manual, which is the source document the California Department of Motor Vehicles uses to write its actual exam.

How it works: Click an answer. The correct choice highlights in green, and you'll see a short explanation. Aim for 85% or better before you sit for the real test in California.

Question 1 of 20

The governor controls:

Engine RPM
When the air compressor pumps air into the air storage tanks
Brake-pedal travel
Trailer hand-valve operation

Correct. The governor cycles the compressor: it cuts the compressor in around 100 psi and cuts it out around 125 psi.

Question 2 of 20

The parts of an air-brake system include:

Air compressor, governor, air storage tanks, foot valve, and brake chambers
Master cylinder, brake fluid, and calipers
Hydraulic pump, lines, and disc rotors
Vacuum booster and reservoir

Correct. Air-brake systems use a compressor, governor, storage tanks, foot valve, and brake chambers — distinct from hydraulic systems used in cars.

Question 3 of 20

For a single vehicle (not a combination) with engine off and brakes released, the maximum allowable air-loss rate is:

1 psi/min
2 psi/min
3 psi/min
4 psi/min

Correct. A single vehicle is allowed no more than 2 psi/min of air loss with engine off and brakes released.

Question 4 of 20

The S-cam:

Is a type of fuel pump
Forces the brake shoes against the drum to provide braking action
Adjusts the slack adjuster
Is the parking-brake control

Correct. When the foot valve is pressed, air pushes the brake-chamber pushrod, which moves the slack adjuster, which rotates the S-cam shaft, forcing the shoes against the drum.

Question 5 of 20

The application pressure gauge shows:

The pressure in the storage tanks
How much pressure is being applied to the brakes when you press the foot valve
Tire pressure
Engine oil pressure

Correct. The application gauge (when present) shows brake-application pressure — useful for spotting brake-system problems on long downgrades.

Question 6 of 20

When brake drums or shoes get very hot, you should:

Park immediately
Continue driving
Pull over and let them cool, but do not apply the parking brake until they have cooled
Throw water on them

Correct. Park where you can let the brakes cool. Do not apply the parking (spring) brake on overheated brakes — it can damage them or cause warpage.

Question 7 of 20

A condition called "brake fade" is most likely on:

Long downgrades
Flat highway
Backing into a dock
Fueling

Correct. Brake fade comes from heat from extended use — most commonly on long, steep downgrades where the brakes are working continuously.

Question 8 of 20

Manual slack adjusters must be adjusted:

Only by a mechanic at the dealership
By the driver, when needed, following manufacturer specifications
Never
Only at the time of vehicle inspection

Correct. Drivers may adjust manual slack adjusters in compliance with manufacturer specifications. Automatic slack adjusters are now standard but still require periodic checking.

Question 9 of 20

When the spring brakes apply automatically as air pressure drops, this typically happens between:

100 and 120 psi
60 and 80 psi
20 and 45 psi
5 and 10 psi

Correct. Spring brakes will fully apply somewhere between 20 and 45 psi as system pressure drops, depending on the vehicle.

Question 10 of 20

Continuous use of the brakes on a long downgrade can cause:

Improved braking
Brake fade — loss of braking effectiveness due to overheating
No effect
Faster wear of the air compressor

Correct. Holding the brakes overheats them and causes brake fade — drums expand and brake compounds lose effectiveness, reducing braking force.

Question 11 of 20

If you must drive a vehicle with manual front-wheel-brake limiting valve, you should keep it in the "normal" position:

Always
Only on slick roads
In the slippery position only
Only when empty

Correct. Keep the front-wheel limiting valve in the "normal" position. Modern trucks rarely have this valve, but if equipped, leaving it in "slippery" reduces front braking and lengthens stopping distance.

Question 12 of 20

In a dual air-brake system, the time required for air pressure to build from 85 to 100 psi should be no more than:

15 seconds
30 seconds
45 seconds
120 seconds

Correct. In dual air-brake systems, air should build from 85 to 100 psi within 45 seconds at engine governed RPM.

Question 13 of 20

Brake fade is the result of:

Cold brakes
Worn linings only
Heat from continuous use, which reduces braking effectiveness
Air leaks

Correct. Brake fade comes from heat. Manage downgrade speed by gear selection plus intermittent firm brake use, not continuous light pressure.

Question 14 of 20

For a combination vehicle (tractor and trailer) with engine off and brakes released, the maximum allowable air-loss rate is:

2 psi/min
3 psi/min
4 psi/min
6 psi/min

Correct. A combination vehicle is allowed no more than 3 psi/min with brakes released, or 4 psi/min with brakes applied.

Question 15 of 20

You are driving a tractor-trailer with the air-pressure gauge dropping rapidly. You should:

Continue to your destination
Pull over safely as soon as possible
Apply the brakes hard
Speed up to reach a safe place

Correct. A rapid drop in air pressure indicates a serious leak. Pull over before the pressure drops to the point where the spring brakes apply and the vehicle stops on the road.

Question 16 of 20

The trailer air-supply control:

Is a yellow diamond knob
Is a red eight-sided (octagonal) knob
Is a green knob
Is the same knob as the parking brake

Correct. The trailer air-supply (tractor protection) is a red eight-sided knob. Push in to supply air to the trailer; pull out to shut off air.

Question 17 of 20

For a single vehicle with engine off and brakes applied, the maximum allowable air-loss rate is:

1 psi/min
2 psi/min
3 psi/min
4 psi/min

Correct. A single vehicle is allowed no more than 3 psi/min with brakes fully applied.

Question 18 of 20

Modern dual-circuit air-brake systems are required so that:

Two drivers can operate the truck
If one part of the system fails, the other still provides braking
The truck looks newer
Air pressure builds faster

Correct. Dual systems separate primary and secondary brake circuits so that a failure in one (rear or trailer) still leaves brakes available on the other axle group.

Question 19 of 20

You should drain the air tanks:

Once a month
Once a year
At the end of every working day
Never

Correct. Drain all air tanks at the end of each working day to remove water and compressor oil that has condensed in the tanks.

Question 20 of 20

Pre-trip air-brake check (Step 1) is to:

Test the parking brake
Test the air leakage rate
Time the air-pressure build-up
Check the slack adjusters

Correct. In the seven-step air-brake check the first step is testing the parking brake — release service brakes, set parking brake, gently try to move the vehicle in low gear.

About the California Air Brakes exam

States typically administer 25 Air Brakes questions and require 80% to pass. Questions cover air-brake system parts, dual systems, supply pressure, brake-system warning, slack adjusters, the parking brake, the spring brake, the pre-trip air-system check, and the proper way to perform a leakage-rate test.

The California Department of Motor Vehicles follows the federal CDL standards established by FMCSA. To earn the Air Brakes credential, you must answer at least 80% of the questions correctly. Many candidates score lower the first time because the test pulls from a large pool — refreshing this page will give you a different mix of questions, drawn from the same authoritative source.

Want more practice? Try the full Air Brakes question bank or browse all California CDL practice tests.