Alaska Doubles/Triples CDL Practice Test

This is a free 20-question practice test for the Doubles/Triples portion of the Alaska Commercial Driver's License knowledge exam. Questions are pulled from a pool of 50 drawn from the AAMVA CDL Manual, which is the source document the Alaska Division of Motor Vehicles uses to write its actual exam.

How it works: Click an answer. The correct choice highlights in green, and you'll see a short explanation. Aim for 85% or better before you sit for the real test in Alaska.

Question 1 of 20

A "doubles" combination uses a tractor plus:

Two trailers connected by a dolly
One trailer
Three trailers
No trailers

Correct. Doubles = tractor + lead semi-trailer + converter dolly + second semi-trailer (which becomes a full trailer once on the dolly).

Question 2 of 20

In a multi-trailer combination, the most violent movement during evasive maneuvers happens at:

The tractor
The first trailer
The last trailer
The cab

Correct. Rearward amplification (crack-the-whip effect) is greatest at the rear-most trailer. The last trailer in a triple can be thrown sideways with much greater force than the tractor.

Question 3 of 20

When pulling a heavy lead trailer and a light second trailer, the rig:

Will be more stable than the reverse
Is more likely to roll the rear trailer
Is illegal
Drives the same as either order

Correct. Heaviest in front, lightest in rear. Heavy at the rear amplifies crack-the-whip and rollover risk.

Question 4 of 20

During a pre-trip on doubles, the trailer-supply line:

Should be open from tractor to rear-most trailer
Should be open at the front but closed at the rear-most trailer
Should be closed everywhere
Should always be disconnected

Correct. The supply line carries air from tractor through every trailer; verify open valves at every coupled connection and a closed valve at the rear of the rear-most trailer.

Question 5 of 20

When inspecting a converter dolly, the pintle hook must:

Lock fully closed around the lunette eye
Be loose
Be cracked
Be replaced quarterly

Correct. The pintle hook must close fully around the lunette eye, with no excessive wear or cracks. Add safety chains as backup.

Question 6 of 20

When coupling the second trailer to the converter dolly:

Position the dolly in front of the second trailer, lower trailer landing gear if necessary, lock the dolly to the lead trailer's pintle hook with safety chains, then back the second trailer onto the fifth wheel
Just push them together
Use the trailer hand valve
Drive past it fast

Correct. Position dolly, secure to lead-trailer pintle, then back second trailer over the fifth wheel and lock as a normal coupling.

Question 7 of 20

Safety chains on a converter dolly are required to:

Prevent the dolly from disconnecting if the pintle hook fails
Decorate the rig
Bind cargo
Add weight

Correct. Safety chains catch the dolly if the pintle hook releases or fails — preventing the trailer behind from breaking loose.

Question 8 of 20

A pintle hook is:

The hitch on the rear of a trailer used to tow another trailer or dolly
The kingpin
The fifth wheel
A type of placard

Correct. The pintle hook is the strong rear-mounted hitch that grips the dolly's lunette eye, allowing one trailer to tow another behind it.

Question 9 of 20

When uncoupling the converter dolly from the lead trailer:

Lower trailer landing gear (if applicable), disconnect air and electrical, remove safety chains, then release pintle hook
Just unhook the chains and pull away
Drive forward fast
Use only the trailer brake

Correct. Standard sequence: support the trailer (landing gear if it is a semi-trailer), disconnect lines, remove chains, release pintle hook.

Question 10 of 20

A "set of doubles" typically refers to:

A tractor pulling two trailers
One tractor with one long trailer
Two tractors and a trailer
Two tractors and two trailers

Correct. A "set of doubles" is one tractor pulling two trailers (typically two pups, each about 28 feet long, in LTL operations).

Question 11 of 20

A converter dolly is:

A small hand truck
A set of axles with a fifth wheel that converts a semi-trailer into a full trailer for use in doubles/triples
A trailer-loading device
A type of brake

Correct. A converter dolly has a small frame, axle(s), and a fifth wheel mounted on top — it transforms a semi-trailer into a full trailer behind another trailer.

Question 12 of 20

Crosswinds are particularly hazardous for:

Empty doubles and triples
Loaded singles
Backing
Slow speeds

Correct. Empty trailers in a multi-trailer rig present a large flat surface to crosswinds — a strong gust can blow the rear trailer over.

Question 13 of 20

When making a lane change in a doubles rig, you should:

Signal early, check mirrors, change lanes gradually
Snap the wheel
Use only the trailer hand valve
Skip the signal

Correct. Early signal, mirror check, gradual lane change. Quick lane changes amplify into the rear trailer.

Question 14 of 20

On a steep downgrade with doubles, you should:

Select a lower gear before starting down and use intermittent firm braking
Coast in neutral
Use only trailer brake
Stay in high gear

Correct. Same rule as any combination vehicle, but plan extra margin: doubles take longer to stop and the rear trailer may push.

Question 15 of 20

When inspecting a doubles or triples rig, you should additionally check:

Each pintle hook, each set of safety chains, each converter dolly, each trailer's lights, brake chamber connections, glad-hands, and shut-off valves
Only the lead trailer
Only the tractor
Only the cargo

Correct. Every connection point and every trailer needs inspection — pintle hooks, chains, dollies, lights, brake lines, glad-hands, and air-supply valves.

Question 16 of 20

A safe practice when starting from a stop with doubles:

Accelerate gently to avoid breakaway sway in the second trailer
Floor the accelerator
Use only the trailer hand valve
Skip first gear

Correct. Sudden acceleration can cause the rear trailer to sway. Start gently in low gear.

Question 17 of 20

A tractor pulling doubles cannot brake as quickly as a tractor pulling a single trailer because:

Doubles are heavier and brake response is delayed in longer air lines
Doubles are lighter
Brakes are bigger
Tractors brake better with doubles

Correct. Greater weight and longer air lines mean longer braking distance. Plan stopping distance with extra margin.

Question 18 of 20

When you encounter a breakaway in your doubles (a trailer separates):

Maintain control of the tractor and lead trailer, brake gently to a controlled stop, set warning devices, and contact dispatch
Brake hard
Speed up
Swerve sharply

Correct. Maintain control of what remains, brake gently and progressively, secure the area with warning devices, contact dispatch.

Question 19 of 20

Drivers should always couple the heaviest trailer:

Behind the tractor (in the front position)
At the rear
In the middle
It does not matter

Correct. Heaviest trailer goes directly behind the tractor; lightest goes at the rear. This minimizes rearward amplification and rollover risk.

Question 20 of 20

When parking a doubles rig:

Park where you can pull straight out — back-out is impractical
Back into any spot
Park in the entrance
Block the lane

Correct. Choose pull-through parking. Multi-trailer rigs cannot back any meaningful distance safely.

About the Alaska Doubles/Triples exam

Most states administer 20 Doubles/Triples questions and require 80% to pass. The exam emphasizes coupling and uncoupling the converter dolly, rearward amplification (the "crack-the-whip" effect), and the unique inspection and handling demands of multi-trailer rigs.

The Alaska Division of Motor Vehicles follows the federal CDL standards established by FMCSA. To earn the Doubles/Triples credential, you must answer at least 80% of the questions correctly. Many candidates score lower the first time because the test pulls from a large pool — refreshing this page will give you a different mix of questions, drawn from the same authoritative source.

Want more practice? Try the full Doubles/Triples question bank or browse all Alaska CDL practice tests.